Cranesmart Systems LMI System - To View the Auxiliary Winches

101 pages

Save Page as PDF

To Next Page

To Previous Page

55 Cranesmart LMI Version R9

To View the Auxiliary Winches

1. Press the Up or Down arrows, (a message is displayed warning the user that the system will change to another winch).

2. Press Accept to Change, (the configuration screen for the new winch will be displayed).

3. Press Select to Cancel.

Main Page

Table of Contents5
Installation Instructions11
Load Cell Link Installation12
- Male/Female Load Cell Installation (7,500, 15,000 & 25,000 Lbs)12
  - Male/Female 7.5/15/25K Load Cell Link Placement Dead-End - for Multiple Parts-Of-Line13
  - Male/Female 7.5/15/25K Load Cell Link Placement on Headache Ball - for Single Part-Of-Line14
- Male/Male Flat Link Load Cell Installation (40,000, 50,000 or 80,000 Lbs.)15
Load Cell Battery Replacement18
Radio Linerider Installation20
- Radio Linerider Installation Overview20
- Hydraulic Boom Linerider Installation Instructions21
  - Installation Steps21
- Lattice Boom Linerider Installation Instructions22
  - Installation Steps22
- Installing the Wire Rope (Hoisting Cable) through Linerider Assembly Instructions24
  - Installation Steps24
Anti-2-Block Installation25
- Counterweight26
Boom Angle Transducer Installation27
Wind Speed Transducer Installation28
Radio Cable Reel with Boom Angle Measurement29
- Cable Reel Assembly29
- Cable Reel Installation30
Level Transducer Installation Instructions35
- Installation Type a - Measuring Machine Tilt (Roll)35
- Installation Type B - Measuring Grade and Super Elevation / Ship List (Roll) and Trim (Pitch)36
- Level Transducer Error Messages37
Battery Replacement for Anti-2-Block, Angle, Cable Reel & Level Transducers38
Boom Direction Transducer - Bdt39
- Mounting the BDT Bracket39
- Tank Tags39
Display Panel Installation41
- Mounting the Display Panel41
- Wiring the Display Panel42
- Alarm Shut-Offs - the White Wire42
  - Basic Wiring Diagram43
- Power Converters44
- Hazardous Location Rated Systems44
- Junction Box44
  - Junction Box Wiring Diagram45
- Alarm Hub46
  - Alarm Hub Wiring Diagram47
- Antenna Installation48
- Shut-Off Bypass Plug52
Display Panel Operations53
- System Start-Up53
  - To Accept the Current Configuration54
  - To Change the Display Panel Configuration54
- Quick Winch Switching55
  - To View the Auxiliary Winches56
  - To Accept the New Winch Configuration57
- Panel Button Functions58
- Menu Navigation59
Operator Permission Level61
- Configure Menu62
  - Select Winch and POL (Parts-Of-Line)62
- Limits Menu62
- System Menu65
- Diagnostic Menu66
Supervisor Permission Level68
- Permissions Level69
  - To Set the Permission Level69
  - To Exit the Setup Menu69
- Calibration Menu70
- Options Menu74
- System Menu77
- Supervisor Enable/Disable Menu79
- Logger Menu79
Display Panel - Operating Screens81
- Primary Operating Screen81
- Secondary Operating Screen81
- Limits Screen83
- Signal Strength Screen84
- Info Screen85
Display Panel - Alarms86
- Alarm Codes87
- Function Shut Offs90
Technical Specifications91
- 7,500Lb Single Line Pull Load Cell91
- 15,000 Single Line Pull Load Cell92
25,000Lb Single Line Pull Load Cell93
40,000Lb Single Line Pull Load Cell94
50,000Lb Single Line Pull Load Cell95
80,000Lb Single Line Pull Load Cell96
Anti-2-Block Switch97
Boom Angle Transducer98
Display Panel99
Alarm Hub100
Wind Speed Transducer101

Cranesmart Systems LMI System - To View the Auxiliary Winches

Table of Contents