CRC Smartwasher SW-37 User Manual

Smartwasher SW-37
Operating Manual
|
5
Installation & Setup Continued
OzzyMat
®
FL-4 Maintenance
1. Make sure the pump is not running.
2. Remove the False Bottom from the sink.
3. Peel away the top layer of the OzzyMat
®
and wring out
any excess uid. Then, dispose of this layer according to
your local regulations.
4. Return the False Bottom to its proper place.
Replacing the OzzyMat
®
1. Make sure the pump is not running.
2.
Remove the False Bottom from the sink.
3. Remove the last layer of the soiled OzzyMat
®
and set to
one side of the lter support grid.
4. Remove a new OzzyMat
®
from its poly bag, unfold the mat
and lay it on top of the lter support grid - white side up.
5. Roll up used OzzyMat
®
and stand vertically against the
side of the sink to drain excess uid. This will allow good
uid to drain from used mat before disposal. Never wring
out OzzyMat
®
prior to disposal.
6. Take the old, used OzzyMat
®
and place into the poly bag
the new mat came in.
7. Return the False Bottom to its proper position.
8. Discard used OzzyMat
®
in accordance with your local
regulations.
OzzyJuice
®
Degreasing Solution
The SmartWasher
®
uses a specially formulated uid which
provides a combination of excellent cleaning characteristics,
safety and nutrition for the Ozzy
®
microbes. OzzyJuice
®
is
provided in ready-to-use containers.
Adding OzzyJuice
®
Slowly pour a full container of
OzzyJuice
®
directly into the
SmartWasher
®
sink. The “Add
Fluid” light should go out when
you have completed this process.
To help monitor and maintain
the proper uid level, the
SmartWasher
®
is equipped with
an “Add Fluid Light”.
When the “Add Fluid” light comes
on the heater in the unit will turn
o until an ENTIRE 20L container
of OzzyJuice
®
is added.
The “Add Fluid” light will shut o
and the heater will come back on once the 20L container of
OzzyJuice
®
is added to the SmartWasher
®
.
Temperature Settings
Your SmartWasher
®
should be plugged in 24 hours a day,
7 days a week to maintain optimal temperature.
Depending on the OzzyJuice
®
solution shipped with your
SmartWasher
®
, the thermostat is factory-set to maintain uid
temperature between 40°C to 46°C (+/-1°). This temperature
provides the optimum condition for eective cleaning and
activity of Ozzy
®
microbes.
The heater will not operate when the uid level becomes
critically low. Lift the sink and check your uid level. When
the “Add Fluid Light” illuminates add 1 (20L) container of
OzzyJuice
®
. If, after a reasonable warm-up period, the uid
temperature seems too hot or too cold, please refer to the
“Troubleshooting” section on page 10 and 11.
If the temperature falls below the recommended minimum,
the system will still clean, but remediation of the hydrocarbons
by the Ozzy
®
microbe colony will slow down. However, the
microbes will not die. The Ozzy
®
colony will become more
active when the uid temperature reaches the appropriate
level.
DO NOT ADD
Water, Solvent, Mineral Spirits, Gasoline or
Kerosene to your SmartWasher
®.
View the “How To” videos on the CRC SmartWasher
®
machine set up and
maintenance at www.crcind.com.au/smartwasher
For technical support visit our website w
ww.crcind.com.au/smartwasher or call us on 1800 224 227

CRC Smartwasher SW-37 Specifications

General

Brand	CRC
Model	Smartwasher SW-37
Category	Washer
Language	English