Crestron DM-RMC-4K-SCALER-C Guide

DO GUIDE
Mounting onto a Rack Rail
The DM-RMC-4K-SCALER-C mounts onto
the front or rear rail of a rack. Position
either the left or right mounting ange of the
device so that the holes align with the holes
in the rack. Then, secure the device to the
rack using two rack mounting screws (not
included).
DO Check the Box
QTY PRODUCT PART NUM.
1 Power Pack, 24 Vdc 1.25 A, 100-240 Vac 2043102
2 Interface Connector, Plug, 4-Pin 2003576
2 Interface Connector, Plug, 5-Pin 2003577
Not Included: Cables, Mounting Screws
DO Make Connections to the Device
Make connections to the DM-RMC-4K-SCALER-C as required for the application.
The DM IN port is a PoDM+ (Power over DM) PD (Powered Device) port. To receive PoDM+, the
DM-RMC-4K-SCALER-C requires a connection to a DigitalMedia™ switcher or other equipment
that has a PoDM+ PSE (Power Sourcing Equipment) port. Any wiring that is connected to a
PoDM+ PSE port is for intra-building use only and should not be connected to a line that runs
outside of the building in which the PSE is located.
NOTE: Connection of the CEN-SWPOE-16 to the POE IN ports of DMC-4K-CO-HD output
cards in a DigitalMedia switcher can provide PoDM+ power to up to eight
DM-RMC-4K-SCALER-C devices.
NOTE: Connection of the DM-RMC-4K-SCALER-C to the included power pack is not required
when PoDM+ is used to power the device.
DM-RMC-4K-SCALER-C/DM-RMC-4K-SCALER-C-DSP
4K DigitalMedia 8G+
®
Receiver and Room Controller with Scaler
The Crestron
®
DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP are generally
identical. For simplicity within this guide, the term “DM-RMC-4K-SCALER-C” is used except
where noted.
DO Install the Device
The DM-RMC-4K-SCALER-C can be mounted onto a at surface or onto a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included),
mount the device onto a at surface such as
a wall or a ceiling.
To/From
RS-232 Device
To IR Controllable
Devices
Balanced Stereo Line
Level Audio Output
To Relay Controllable
Devices
Ground
10BASE-T/100BASE-TX
Ethernet to Local Network
Device
HDMI
®
Digital Video and
Audio Output
From DM
®
Switcher,
Transmitter, or Other
DM Device or to
HDBaseT
®
Device
From Power Pack
(Included)

Crestron DM-RMC-4K-SCALER-C Specifications

General

Baud rate	115200 Bd
Product color	Black
LED indicators	Yes
Heat dissipation	63 BTU/h
Housing material	Metal
Scaled resolutions	1920 x 1080, 2560 x 1600, 3840 x 2160, 4096 x 2160
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
AC adapter frequency	50/60 Hz
AC adapter input voltage	100-240 V
Power consumption (typical)	18 W
RJ-45 ports quantity	2
Number of HDMI outputs	1
Maximum pixel clock	300 MHz
Channel separation (1 kHz)	90 dB
Signal-to-Noise Ratio (SNR)	95 dB

Weight and Dimensions

Depth	28 mm
Width	137 mm
Height	318 mm
Weight	625 g