Why is the DLINK LED flashing green on my CREVIS FnIO G?
If the DLINK LED is flashing green, it indicates that cyclic transmission is not being performed. To resolve this, check the status of the master.
How to troubleshoot if all LEDs are off on CREVIS FnIO G Adapter?
If all the LEDs on your CREVIS Adapter are off, it could be due to: * No power. Check the main power cable. * The system power is not being supplied. Contact the sales team and send the module for repair.
What to do if L RUN LED turns off on CREVIS FnIO G?
If the L RUN LED on your CREVIS Adapter turns off, it might be because: * The device is not online or powered. Check the main power cable. * The hardware is resetting. Check the communication cable. * The device has timed out. Verify the configuration with respect to CC-Link in the PLC program.
Why is the I/O LED red on my CREVIS Adapter?
If the I/O LED on your CREVIS Adapter is red, it indicates a failure in exchanging I/O data. To resolve this, check the status of the expansion I/O connection.
What to do if Field Power LED turns off on CREVIS Adapter?
If the Field Power LED turns off, it means that field power is not being supplied. You should check the main power cable. If the issue persists, contact the sales team and send the module for repair.
Why is the IOS LED off on my CREVIS FnIO G?
If the IOS LED is off, it indicates that the device may not be powered. Check the main power cable to ensure the adapter is receiving power.
What does MOD LED flashing green mean on CREVIS I/O Systems?
If the MOD LED on your CREVIS I/O Systems flashes green, it indicates a failure of the initialization EEPROM parameter. In this case, it is recommended to contact the Sales team and send the module for repair.
Why is the IOS LED on my CREVIS FnIO G Adapter red?
The IOS LED might be red due to several reasons: * One or more expansion modules are in a fault state. * An invalid expansion module ID was detected. * Input/Output Size overflowed. * There are too many expansion modules. * Initialization failure. * Communication failure. * The expansion module configuration changed. * There is a mismatch in the vendor code between the adapter and expansion module. To resolve this: * Use up to 32 expansion slots. * Ensure the total IO size is not exceeded. * Check the status of the expansion IO connection. * Check the vendor code of the module.
Why RUN LED flashes red on CREVIS I/O Systems?
If the RUN LED on your CREVIS I/O Systems flashes red, it indicates a failure of module configuration. To resolve this, check that the module hardware and software configurations are the same.
How to troubleshoot all LEDs turning off on CREVIS I/O Systems?
If all LEDs on your CREVIS I/O Systems are off, it could be due to a lack of power. First, check the main power cable to ensure it's properly connected. If the power cable is fine, the system power might not be supplied correctly. In this case, it is recommended to contact the Sales team and send the module for repair.
Provides essential safety instructions for using the device, covering symbols, notes, and certifications.
Details the electrical connections and interfaces within the G-Series system.
Explains the data flow for process image between network adapter and expansion modules.
Provides overall specifications including power, environment, and certifications.
Details interface specifications for programmable and physical connections.
Outlines Ethernet connection capabilities for different models.
Describes the main GN-9371/72/73 MODBUS programmable I/O module.
Explains the function of each LED indicator on the module.
Details the RJ-45 and serial port pin assignments and functions.
Describes the operation of toggle switches and push buttons on the module.
Details the removable terminal block (RTB) connections.
Provides a detailed description of all pins on the module.
Shows the physical dimensions of the module.
Instructions on how to mount the module onto a DIN rail.
Instructions on how to safely remove the module from a DIN rail.
Details the removable terminal block (RTB) and its wiring.
Explains the correct method for wiring the module.
Guides connection to IO Guide Pro using Modbus RTU serial communication.
Guides connection to IO Guide Pro using Modbus TCP network communication.
Explains how to check and confirm network settings like IP address.
Details the IP address setting using BOOTP or DHCP protocols.
Manual procedure for setting the device's IP address.
Configures serial communication parameters for RS232/RS485.
How to reset the device to factory default settings.
Explains the Real-Time Clock function and its settings.
Accessing and using the module's web server interface.
Details the default IP address settings for the device.
Instructions for downloading and installing the required CODESYS software.
Steps for basic CODESYS configuration, including XML installation.
Guide to creating a new project within CODESYS.
Overview of the CODESYS development environment interface.
How to set up input/output modules within CODESYS.
Configuration steps for Modbus TCP communication.
Configuring the device as a Modbus TCP master.
Configuring the device as a Modbus TCP slave.
Setting up network variables for communication.
Procedures for downloading applications and monitoring device status.
Configuring symbolic variables for OPC communication.
Configuring register 1614 for Modbus RTU master communication.
Adding Modbus COM devices via the serial port in the device tree.
Configuring serial port parameters for Modbus RTU master.
Adding the web visualization manager to the project.
Configuring web visualization options and window size.
Adding visualization objects to the application.
Procedures for downloading and uploading project source files.
Steps to add and configure the Recipe Manager object.
Adding and configuring the Trace object for variable monitoring.
How to set breakpoints in the program for debugging.
Adding new online users and configuring login credentials.
Instructions for upgrading the device firmware via Ethernet.
Diagnosing issues based on the status of LED indicators.
Troubleshooting steps for network communication problems.
Details the MODBUS register map and bit map for interface.
Lists and describes supported MODBUS function codes.
Example of connecting a Beijer HMI master to a PLC slave via TCP.
Example of connecting a Beijer HMI master to a PLC slave via RTU.
To Next Page
General