Crown D-150A - Page 6

Stereo
Specifications
Output Power:
80 watts
per
channel
minimum
RMS
(both channels
operating)
into
an
8 ohm
load
over
a
bandwidth of 1
Hz-20KHz
at a
rated
RMS
sum
total
harmonic distortion
of
0.05%
of
the
fundamental
output
voltage.
Frequency Response:
±0.
1 d B
DC-20KHzat
1
watt
into
8
ohms;
±ldB
DC-lOOKHz.
IKHz Power:
90 watts
RMS into
8
ohms,
per
channel,
both channels
operating,
0.
1%
total
harmonic
distortion.
Harmonic Distortion:
Less
than
0.001%
from
20-400 Hz
and increasing
linearly
to
0.05%
at
20KHz
at
80
watts
RMS
per channel
into
8 ohms.
LM,
Distortion
S.M.P.T.E.
(60Hz-7KHz
4:1):
Less
than
0.05%
from
0.01 watt
to
0.25 watts
and
less
than
0.01%
from
0.25 watts
to
80
watts into
8 ohms,
per
channel.
Slewing
Rate: 6 volts
per
microsecond
(slewing
rate
is
the
maximum
value of the
first
derivative
of
the
output
signal,
or
the
maximum
slope
of the
output
signal).
Damping
Factor:
Greater
than
400,
DC-400Hz
into
8
ohms.
Output
Impedance:
Less than
15
milliohms
in
series with
less
than
3 microhenries.
Load
Impedance:
Rated
for
8 ohm
usage;
safely
drives
any
load
including
completely
reactive
loads.
Voltage
Gain: 20.6
±2%
or
26.3±2dB at
maximum
gain.
Input
Sensitivity: 1.19
volts
±2%
for
80 watts
into
8
ohms.
Output Signal:
Unbalanced,
dual
channel.
Monaural
Specifications
Output
Power: 1
60
watts
minimum
RMSintoa
16ohm
load over
a bandwidth
of
lHz-20KHz
at
a
rated
RMS
sum total harmonic
distortion
of
0.05%
of
the
fundamental
output
voltage.
Frequency
Response
(IKHz
Power):
±0.15dB
DC-
20KHz
at 1 watt into
16 ohms;
±ldB
DC-60KHz,
180
watts RMS into
16 ohms.
Harmonic Distortion:
Less
than
0.001%
from
20-400Hz
and
increasing linearly
to
0.05%
at
20KHz
at
160
watts
into
16
ohms.
LM. Distortion
S.M.P.T.E.
(60Hz-7KHz
4:1):
Less
than
0.05%
from 0.01
watts
to
0.25
watts
and
less
than
0.01%
from
0.25 watts
to
160 watts
into
16
ohms,
per
channel.
Slewing
rate:
12
volts
per
microsecond.
Damping
Factor:
Greater
than
400, DC-400Hz
into
16
ohms.
Output
Impedance:
Less
than
30
milliohms
in
series
with
less
than
6
microhenries.
Load
Impedance:
Rated
for
16
ohm
usage;
safely
drives
any load
including
completely
reactive
loads.
Voltage
Gain:
41.2
±2%
for
160
watts
into
16
ohms.
Input
Sensitivity:
1.19
volts
±2%
for
160
watts
into
16
ohms.
Output
Signal:
Balanced,
single
channel.
R-2