Cub Cadet LT1022 User Manual (English)

Questions and Answers:

J
John WallAug 12, 2025
Why Cub Cadet Lawn Mower engine fails to start?
- K
  Kimberly MckinneyAug 12, 2025
  Your Cub Cadet lawn mower engine might fail to start due to several reasons: * The PTO/Blade Engage knob might be engaged - place it in the disengaged (OFF) position. * The parking brake might not be engaged - engage the parking brake. * Spark plug wire(s) might be disconnected - connect the wire to the spark plug. * The throttle control lever might not be in the correct starting position - place the throttle lever to the FAST position. * The choke might not be activated - pull out the CHOKE control. * The fuel line might be blocked - clean the fuel line or replace the fuel filter. * The spark plug might be faulty - clean, adjust the gap to .040” or replace the plug. * The engine might be flooded - crank the engine with the throttle in the FAST position.
M
Michael PatrickAug 16, 2025
Why Cub Cadet Lawn Mower uneven cut?
- A
  Aaron HornAug 16, 2025
  An uneven cut with your Cub Cadet lawn mower may be due to: * The deck not being balanced properly - perform a side-to-side deck adjustment. * A dull blade - sharpen or replace the blade. * Uneven tire pressure - check the tire pressure in all four tires.
T
Timothy CastilloAug 20, 2025
What to do if Cub Cadet Lawn Mower engine runs erratic?
- M
  madelinemartinezAug 20, 2025
  If your Cub Cadet lawn mower engine is running erratically, consider the following: * If the unit is running with CHOKE activated, push the CHOKE control in. * If the spark plug wire(s) are loose, connect and tighten them. * If the fuel line is blocked or the fuel is stale, clean the fuel line and fill the tank with clean, fresh gasoline (less than 30 days old). * If the vent in the gas cap is plugged, clear the vent or replace the cap if damaged. * If there is water or dirt in the fuel system, drain the fuel tank and refill with clean, fresh gasoline (less than 30 days old). * If the air cleaner is dirty, replace the air cleaner paper element or clean the foam precleaner.
K
Kimberly MillerAug 23, 2025
What to do if Cub Cadet LT1022 Lawn Mower idles poorly?
- P
  Patricia ReedAug 23, 2025
  If your Cub Cadet lawn mower idles poorly: * The spark plug might be fouled, faulty, or have a gap that is too wide - replace the spark plug. * The air cleaner might be dirty - replace the air cleaner cartridge/element or clean the pre-cleaner.
K
Katherine BoydAug 27, 2025
What to do if Cub Cadet LT1022 Lawn Mower engine overheats?
- S
  simsjesseAug 27, 2025
  If your Cub Cadet lawn mower engine overheats: * Check the engine oil level. If it's low, fill the crankcase with the proper capacity and weight of oil. * Ensure that air flow is not restricted. Clean any grass clippings and debris from around the engine’s cooling fins and blower housing.
R
rebeccarobinsonAug 31, 2025
Why Cub Cadet LT1022 Lawn Mower has excessive vibration?
- C
  Casey WrightAug 31, 2025
  Excessive vibration in your Cub Cadet lawn mower can be caused by: * A cutting blade that is loose or unbalanced - tighten the blade and spindle. * A damaged or bent cutting blade - balance or replace the blade.
S
Sharon JamesSep 4, 2025
Why Cub Cadet LT1022 will not mulch grass?
- N
  nashkevinSep 4, 2025
  If your Cub Cadet lawn mower isn't mulching grass effectively, it could be due to: * Engine speed being too low - place the throttle in the FAST (rabbit) position. * Wet grass - avoid mowing when the grass is wet; wait until it's dry. * Excessively high grass - mow once at a high cutting height, then mow again at the desired height or make a narrower cutting swath. * A dull blade - sharpen or replace the blade.
A
Arthur VanceSep 8, 2025
Why Cub Cadet Lawn Mower engine hesitates at high RPM?
- J
  James RamseySep 8, 2025
  If your Cub Cadet lawn mower engine hesitates at high RPM, the spark plug gap may be too close. Remove the spark plug and reset the gap to .040”.

Cub Cadet LT1022 Specifications

General

Engine Power	22 HP
Transmission	Hydrostatic
Cylinders	2
Drive	2WD
Number of Blades	2
Turning Radius	18 inches
Cutting Height	1-4 inches
Front Tire Size	15 x 6 - 6
Deck Material	Steel
Wheel Size (Front)	15 x 6 - 6