Cudy RE300 User Manual

Quick Installation
Guide
Hardware Overview
Default Parameters
Web Setup: http://ap.setup/
Default IP: 192.168.10.254
Password: admin
SSID:Cudy-RE300
Power On/Off
Mode Selector
WPS Button
WLAN LED
Power/WPS LED
WAN/LAN LED
LAN LED
LAN Port
WAN/LAN Port
Reset Button
1
2
3
4
5
6
7
8
9
10
3
Reset
10
1
2
WPS
8 9
4
5
6
7
Repeater Mode
1. Switch the mode selector to Repeater position.
2. Plug the Device into an electrical outlet near your Wi-Fi router.
3. Shift the power switch to ON and wait until the POWER LED is on and
solid green.
1. Disconnect the Ethernet (Wired) connection if using a laptop or PC.
2. Connect your device to extender’s Wi-Fi Cudy-RE300.
Power ON
Connect to the Device
Not connected
Connections are available
Wireless Network Connection
Cudy-RE300
Connect
Connect automatically
Method One: Using Web browser
1
2
3
4
1. Launch a web browser and type 192.168.10.254 (or http://ap.setup/)
in the address field. Enter admin for password to login.
2.Click Wizard.
Configure
Login
admin
English
Wi-FI Range Extender
This Device Router
Repeater
WAN Type
Device IP
Gateway
DNS1
DNS2
WAN MAC
Cudy-xxxx
5
00h:01m
M78N_V3130.0604
Wi-Fi SSID
Channel
Uptime
Firmware
Repeater
192.168.10.254
192.168.10.254
0.0.0.0
0.0.0.0
82:3F:5D:06:1A:FC
Device Information
Speed
0 KB/S
Clients
1
Disconnect
Internet
Status Wizard Wi-Fi Setup
Relocate
3. Select a Wi-Fi SSID of your router (Host Wi-Fi) and enter the password.
Either keep the same SSID as your host Wi-Fi or create a new name for
the extended network.
4. Verify your wireless settings and click Connect. The WLAN LEDs
should turn on and stay solid,indicating successful connections.
1. Plug the Device into an electrical outlet about halfway between your
router(Host Wi-Fi) and the Wi-Fi dead zone. The location you choose
must be within the range of your existing host Wi-Fi.
2. Wait until the WLAN LEDs are ON. If the signal is weak, relocate it
closer to the router to achieve a good (or better) signal quality.
Repeater Wizard
Connect
Select a Wi-Fi Manually enter
Cudy-XXXX
Cudy-XXXX-5G
Cudy-Guest
Connect to:
Wi-Fi Password:
Repeater SSID:

Cudy RE300 Specifications

General

Brand	Cudy
Model	RE300
Category	Repeater
Language	English

Summary

Hardware Overview

Repeater Mode Setup

Method One: Using Web Browser

Configure the Wi-Fi extender via a web browser by connecting to its default IP address and using the setup wizard.

Configure Extended Network

Select the host Wi-Fi SSID, enter its password, and optionally rename the extended network.

Relocate for Optimal Signal

Place the device halfway between the router and dead zone, ensuring it's within the host Wi-Fi range.

Method Two: Using WPS Button

WPS Connection Steps

Connect the extender to the router wirelessly by pressing the WPS buttons on both devices within a two-minute window.

Router Mode and Access Point Mode

Change Login Password

Firmware Upgrade

Frequently Asked Questions

Login Window Issues

Troubleshooting steps for when the login window does not appear, including checking connection and IP settings.

No Wi-Fi Signal Found

Steps to resolve issues where the Wi-Fi signal cannot be found by devices, including reset and testing.

Reset to Defaults

Procedure to reset the extender to factory default settings by pressing the reset button.

Forgotten Login Credentials

Instructions to restore factory settings if the Wi-Fi password or login page credentials are forgotten.

Finding Optimal Placement

Guidance on locating the best position for the extender to maximize Wi-Fi signal strength.