Curtis ThermoPro G3 Series User Manual

Non-Brew Programming Menu (cont.)
Brew Count Total - when accessed, displays the total brew cycles on the brewer. It cannot be reset. The
display returns to the previous screen automatically after a few seconds.
Cold Brew Lock - adjusts the temperature at which the brewer will brew coffee when the BREW button is
pressed (Ready to BrewBQQFBSTPOUIFEJTQMBZ5IFGBDUPSZEFGBVMUTFUUJOHJT'¡$CFMPXUIFXBUFSUBOL
temperature setting. This feature also adjusts the temperature at which the heating element turns on to reheat
UIFXBUFSJOUIFUBOL5IFBWBJMBCMFTFUUJOHTBSF¡'¡'¡$BOE0GG0ODFBDDFTTFEQSFTTŻ or Ź to
choose the desired setting. Then press ~ to set and exit.
Master Reset - resets the brewer universal control module (UCM) to the factory default settings. Once
accessed, “Are You Sure?” will appear on the display. Press Ż for Yes or Ź for No.
Service Call - sets the service phone number that appears on the display when the UCM detects a SENSOR
ERROR or WATER ERROR . Once accessed, press Ż or Ź to choose the number to be changed. Then press
~ repeatedly to change the number value. Press Ż or Ź to choose the next number to change or choose exit
and press ~.
Access Code - sets the access code entered to access programming mode. The factory default is 1-2-3-4.
Once accessed, press Ż or Ź to choose the number to change. Then press ~ repeatedly to change the
number value (the range is 1 to 4). Press Ż or Ź to choose the next number to change or choose exit and
press ~.
Banner Name - changes the company name that appears on the display. The factory default is Curtis. No
name appears when all blanks are entered. Once accessed, press Ż or Ź to choose the letter to change.
Then press
~ repeatedly to change the number value. Press Ż or Ź to choose the next number to change or
choose ex and press ~ to exit.
Warmer Auto-Off - (GEMS, GEMT, GEMSIF, GEMTIF models) adjusts the length of time that elapses before
the dispenser warmer shuts off automatically. This function takes priority over the quality timer. The factory
EFGBVMUTFUUJOHGPS(&.4*'(&.5*'JTIPVST'PS(&.4(&.5UIFEFGBVMUJTiEJTBCMFEw5IFTFUUJOHSBOHFJT
1 to 12 hours. Once accessed, press Ż or Ź to adjust the number of hours. Then press ~ to set and exit.
P-Maintenance - turns on/off and adjusts the P-Maintenance (preventive maintenance) brew monitor.
The factory default setting is Off. When On, the UCM measures the number of gallons brewed before the
1.BJOUFOBODFSFNJOEFSBQQFBSTPOUIFEJTQMBZ5IFTFUUJOHSBOHFJTUPHBMMPOTMJUFST0ODF
accessed, press Ż or Ź to choose the desired setting, then, press
~ to exit.
Beeper On/Off - turns the beeper that is heard each time a button is pressed on or off. The factory default
setting is On. Once accessed, press Ż or Ź to choose the desired setting. Then, press ~ to exit.
Drip-out Mode - TFUTUIFESJQPVUNPEFUJNFS"GUFSXBUFSTUPQTnPXJOHJUBMMPXTBEEJUJPOBMUJNFGPSUIFDPGGFF
to drain from the brew basket before the brew basket lock releases. The factory default is 2 min. This feature
SFEVDFTUIFDIBODFUIBUUIFCSFXCBTLFUXJMMCFSFNPWFEUPPFBSMZ5IFTFUUJOHSBOHFJTUPNJOVUFT0ODF
accessed, press Ż or Ź to choose the desired setting, then, press ~ to exit.
Warmers Default - (Gemini models) sets the warmer temperature. The factory default setting is MED. The
BWBJMBCMFTFUUJOHTBSF0GG)*()'¡$.&%'¡$PS-08'¡$0ODFBDDFTTFE
press Ż or Ź to choose the desired setting, then press ~. On twin brewers press Ż or Ź to choose the
desired setting for the second warmer, then press ~. Press ~ to exit.
*Off option not available on GEMX series models.
(&.*'BOE(&.9POMZCBTFEPOBCSFXUFNQFSBUVSFPG¡'¡$
continued...
PROGRAMMING GUIDE PG2
8$130(3"..*/((6*%&ø H

Curtis ThermoPro G3 Series Specifications

General

Brand	Curtis
Model	ThermoPro G3 Series
Category	Brewing Systems
Language	English