Curtis ThermoPro G3 Series User Manual

PROGRAMMING GUIDE PG2
8$130(3"..*/((6*%&ø H
Non-Brew Programming Menu (cont.)
Display Brew Time - turns the display of the brew time during brewing On or Off. The factory default setting is
On. Once accessed, press Ż or Ź to choose the desired setting, then press ~ to exit.
Display Messages - turns display of the message “Rinse Server Before Brewing” On or Off The factory default
setting is On. Once accessed, press Ż or Ź to choose the desired setting, then press
~ to exit.
[QT] Display Timers [On/Off] - (some models, QT Alarm must be on) turns the quality timer countdown
display On or Off. The factory default setting is Off. Once accessed, press Ż or Ź to choose the desired
setting. Then, press
~ to exit.
QT Alarm On/Off - (Gemini models) turns the quality timer audio alarm On or Off. The factory default setting
is On for GEMS/GEMT models, Off for GEMIF and GEMX models. An audible alarm goes off when the quality
timer has expired. Once accessed, press Ż or Ź to choose the desired setting. Then, press
~ to exit.
Satellite Color - (GEMX series models only) changes the color scheme of the quality timer LEDs on the
dispenser (satellite). Once accessed, press Ż or Ź to choose the desired color to indicate “fresh” (On). Press
~ to save, then press Ż or Ź to choose the desired color to indicate “expired”. Press ~ to save and exit.
Server Lockout - (GEMX series models only) turns the lockout feature On or Off. The factory default setting
JT0GG8IFOTFUUP0OUIF#3&8CVUUPOJTEJTBCMFEXIFOUIFSFJTnVJEJOUIFEJTQFOTFSQSPWJEFEUIBUBO*3
equipped dispenser is in use (LOCKED appears on the display). Once accessed, press Ż or Ź to choose the
desired setting. Press ~ to save and exit.
Brew Button Programming Menu
8IFOZPVmSTUFOUFSUIF#SFX#VUUPO1SPHSBNNJOHNFOVZPVXJMMCFBTLFEUPTFMFDUQSFTTB#3&8CVUUPOUP
DIBOHFUIFTFUUJOHTGPS5PQSPHSBNNPSFUIBOPOF#3&8CVUUPOmOJTIQSPHSBNNJOHUIFmSTUUIFOQSFTTŹ until
Exit appears on the display. Press
~ to exit, then re-enter the Brew Button Program to program the next one. The
default brew settings assume that the amber AFS spray head is installed.
Brew by Volume - BEKVTUTUIFWPMVNFCSFXFE5IFGBDUPSZEFGBVMUTFUUJOHTBSF-"3(&P[P[-
NM
.&%*6.P[P[-NM 4."--P[P[-NM8JUIBEJTQFOTFSJO
place, press the BREW button that is illuminated. When the desired volume is reached, press the same BREW
button again to stop the brew cycle and set the volume.
* Not applicable to TP1 series.
** This is the LARGE setting for TP1 series brewers.
continued...
Select
~
Select
~
Select
~
Select
~
Select Button...
<-- Select -->
Press BREW
Brew Button Prog
<-- Select -->
Pulse Brew
<-- Select -->
Brew by Time
<-- Select -->
Press
~
Exit
<-- Select -->
Pre-Infusion
<-- Select -->
Pulse Brew
<-- Select -->
Brew by Volume
<-- Select -->
Bypass On/Off
<-- Select -->
Press
~

Curtis ThermoPro G3 Series Specifications

General

Brand	Curtis
Model	ThermoPro G3 Series
Category	Brewing Systems
Language	English