CyberPower RMCARD205 Quick Start Guides

K01-0000449-01
Quick Start Guide
REMOTE MANAGEMENT CARD
RMCARD205
RMCARD305
The Remote Management Card allows a UPS/ATS
system and environmental sensor to be managed,
monitored, and configured.
INSTALLATION GUIDE
5. (Optional) To connect with the
environmental sensor, use a RJ45
Ethernet cable. Connect one end to
the Universal port on the RMCARD
and the other end into the sensor.
For more information, please see
the ENVIROSENOR user’s manual.
NOTE: The CyberPower Remote Management Card is hot-swappable,
so you do not need to turn off the device to install it.
4. Connect an Ethernet cable to the
Ethernet port of the CyberPower
Remote Management Card.
3. Insert and tighten the retaining
screws.
2. Install the CyberPower
Remote Management Card
into the expansion slot.
1. Remove the two retaining
screws of the expansion slot,
and then remove the cover.
Definitions for LED Indicators
Step 2. Configure the IP address for the CyberPower
Remote Management Card
Method 1: Using the Power Device Network Utility
1. Install the Power Device Network Utility available for download on the
Network Power Management product web page at www.CyberPower.com.
2. After installation completes, run the “Power Device Network Utility”.
3. The main dialog of the Power Device Network Utility program is shown
in Figure 1. The configuration tool will display all CyberPower Remote
Management devices present on the same network subnet. The
"Refresh" button is used to search the local network subnet again.
4. Select the Remote Management Card you are setting up. Click on the
Tools menu and select “Device Setup” or double click the Remote
Management Card you want to configure.
5. You can modify the IP Address,
Subnet Mask, and Gateway
address for the Device MAC
Address listed in the Device
Network Settings window, as
shown in Figure 2. The factory
default IP Address is
192.168.20.177 and the default
Subnet Mask is 255.255.255.0.
6. Modify the IP, subnet mask or
gateway address. Enter the new
addresses into the corresponding
fields and then click “Save”.
Link LED color
Off
On(Yellow)
Tx/Rx LED color
Off
On(Green)
Flash
Condition
The Remote Management Card is not
connected to the Network/ or the Remote
Management Card power is off
The Remote Management Card is connected
to the Network
The Remote Management Card power is off
The Remote Management Card power is on
- Receiving/transmitting data packet
- Reset finished
Step 1. Hardware Installation
Figure 1. The main window of the “Power Device Network Utility” program.
Figure 2. The Device Network setting window.
RMCARD205 RMCARD305
Tx/Rx
Link
Universal
RMCARD205
CyberPower
CyberPower
Universal
Tx/Rx
RMCARD205
erPower
sal
Tx/Rx
RMCARD205
Universal
Link
Tx/Rx
RMCARD305
CyberPower
RMCARD305
CyberPower
Tx/Rx
RMCARD305
CyberPower
sal
Universal
Tx/Rx
LINK Indicator
Tx/Rx Indicator
Ethernet Port
Universal Port
RMCARD305
Tx/RxLinkUniversal
RMCARD205
Tx/RxLinkUniversal

CyberPower RMCARD205 Specifications

General

AC outlets quantity	- AC outlet(s)
Ethernet LAN (RJ-45) ports	2
Sustainability compliance	Yes
Sustainability certificates	CE, Federal Communications Commission (FCC), RoHS
Country of origin	China
Quantity	1
Product type	Network management card
Product color	Black, Blue
Cabling technology	10/100
Ethernet LAN data rates	10, 100 Mbit/s
Ethernet interface type	Fast Ethernet
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 15000 m
Storage temperature (T-T)	-10 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Supported network protocols	IPv4/v6, SNMPv1/v3, HTTP/HTTPs, TCP/IP, UDP, DHCP, NTP, DNS, SMTP, SSH, SSL, TLS, Telnet, FTP, and Syslog
Cables included	Serial

Weight and Dimensions

Depth	76.5 mm
Width	54 mm
Height	36.1 mm
Weight	160 g
Package depth	60 mm
Package width	170 mm
Package height	165 mm
Package weight	300 g
Dimensions (WxDxH)	172 x 60 x 165 mm