CyberPower RMCARD305 User Manual (English)

Other manuals for CyberPower RMCARD305

Quick Start Guide18 pages

Quick Start Guides2 pages

Questions and Answers:

A
Alex YangAug 8, 2025
What to do if unable to configure CyberPower Network Card?
- T
  Tina SullivanAug 8, 2025
  If you're unable to configure the CyberPower Network Card, first check the LED status. A normal condition is when both the yellow and green LEDs are on. If the green LED is off, ensure the Remote Management Card is properly seated in the UPS and that the UPS power is connected to a working electrical outlet. If the yellow LED is off, verify that the network connection is good. Also, make sure the PC you are using is on the same network subnet as the Remote Management Card.
D
Dorothy MorrisAug 13, 2025
What to do if I am unable to access the Web Interface of CyberPower PCI Card?
- M
  Mrs. Shelia WilliamsAug 13, 2025
  If you can't access the Web Interface for your CyberPower PCI Card, first, make sure you can ping the RMCARD. Second, check that you're using the correct URL. Finally, verify that HTTP/HTTPS access is enabled by logging into the card using a CLI (Telnet or SSH client).
K
Kevin McintoshAug 19, 2025
What to do if I am unable to ping the Remote Management Card on my CyberPower PCI Card?
- V
  Victoria McconnellAug 19, 2025
  If you are unable to ping the Remote Management Card of your CyberPower PCI Card, try using method 1 and/or method 2 to get or set a correct IP address for the card. Also, if the PC being used is on a different network subnet from the Remote Management Card, verify the setting of the subnet mask and the IP address of the gateway.
A
Allen ParrishAug 23, 2025
How to configure CyberPower PCI Card if unable to configure the Remote Management Card?
- C
  cfosterAug 23, 2025
  If you are having trouble configuring the Remote Management Card of your CyberPower PCI Card using method 1 or method 2: * Check the LED status. It is normal when the yellow and green LEDs are both on. * If the green LED is off, check if the Remote Management Card is properly seated in the device and that the device has power. * If the yellow LED is off, make sure the network connection is good. * Ensure the PC being used is on the same local network subnet as the CyberPower device you are trying to communicate with. * Ensure the Jumper on the Reset Pin is correctly installed.
A
Anthony GrayAug 28, 2025
What to do if CyberPower PCI Card is unable to receive traps?
- J
  Jacob WarnerAug 28, 2025
  To resolve issues with your CyberPower PCI Card not receiving traps, ensure that the trap types (SNMPv1/SNMPv3) and trap receiver are configured correctly. Also, ensure the IP address of the gateway is configured correctly if the RMCARD and NMS are on a different network.
D
David KelleySep 3, 2025
Why I am unable to operate a SNMP get/set on CyberPower PCI Card?
- A
  Andres BowenSep 3, 2025
  To resolve issues with operating a SNMP get/set on your CyberPower PCI Card: for SNMPv1, verify the community name; for SNMPv3, verify the user profile configuration.

CyberPower RMCARD305 Specifications

General

Remote Management	Yes
Type	Remote Management Card
Device Type	Network Management Card
Compatibility	CyberPower UPS
Network Interface	Ethernet
Interface	SNMP, Web, Telnet, SSH
Protocols	HTTP, HTTPS, SNMP, SSH
Features	Remote monitoring and control
Weight	0.1 lbs
Power Requirements	Powered by UPS

Related product manuals

CyberPower RMCARD205

83 pages

CyberPower CPUAC1U1300

1 page

CyberPower CPUDC1U2000

1 page

CyberPower RMCARD305 User Manual

Table of Contents

Other manuals for CyberPower RMCARD305

Questions and Answers:

CyberPower RMCARD305 Specifications

Related product manuals