7. Remove the blank plate.
A. Using a Phillips head screwdriver, remove the two
screws securing the blank plate in place. See
Figure 4.
B. Remove blank plate.
Screw (2)
Blank Plate
Figure 4
Controller Cover
Power
Supply
Cable
Controller Board
Screw (2)
9. Connect power supply cable to controller board.
A. Using a Phillips Screwdriver, remove the two screws
securing the controller cover. See Figure 5.
B. Remove cover.
C. Push power supply cable through hole in controller
cover.
D. Firmly press power supply cable jack into the
connector on the controller board.
8. Install power supply.
A. Install power supply in place of blank plate that
was removed in step 7B.
B. Using a Phillips head screwdriver, install the two
screws (removed in step 7A) securing the power
supply. See Figure 4.
C. Route power supply cable (follow existing cables)
up through frame to control board.
Figure 5
F. Using a Phillips screwdriver, install and tighten the
two screws removed in step 9A.
G. Secure power supply cable to the other cables
using the cable tie.
10. Reinstall left shroud.
A. Place left shroud in place.
B. Using a Phillips screwdriver, install the ten screws
and two washers securing the shroud removed in
step 6A.
C. Securely tighten all screws.
11. Reinstall access cover.
A. While being sure not pinch any cables, hold the
access cover in place. See Figure 2.
B. Using a Phillips screwdriver, install and tighten
the two upper screws fi rst (removed in step 5B).
NOTE: Do not over tighten screws.
C. Install and tighten the two lower screws (removed
in step 5A). NOTE: Do not over tighten screws.
12. Install warning decals.
A. Peel off backing and install the two warning decals
as shown in Figures 6 & 7. NOTE: The “Disconnect
Power” decal must be installed in location shown in
Figure 6. The “Medical Inlet” decal must be installed
in location shown in Figure 7.
F
o
r
c
o
n
n
e
c
t
i
o
n
t
o
a
M
e
d
i
c
a
l
G
r
a
d
e
o
u
t
l
e
t
o
n
ly
t
o
e
n
s
u
r
e
p
r
o
p
e
r
g
r
o
u
n
d
i
n
g
.
V
o
l
t
a
g
e
:
1
0
0
-
2
4
0
V
A
C
~
5
0
/
6
0
H
z
DE-
195
47
-4
W
A
R
N
I
N
G
13. Test unit for proper operation.
CM000240 E
ɈɌɄɅɘɑɂɌȿ
ɉɂɌȺɇɂȿ,
ɉɊȿɀȾȿ ɑȿɆ
ɉɊɂɋɌɍɉȺɌɖ
Ʉ ɈȻɋɅɍɀɂȼȺɇɂɘ.
ɉɊȿȾɍɉɊȿɀȾȿɇɂȿ
For connection to a Medical Grade
outlet only to ensure proper grounding.
Voltage: 100-240 VAC~
50/60Hz
0.75 Amps
1-Phase
DE-19547-4
WARNING
Figure 7
Figure 6
E. Reinstall controller cover.
Cybex
®
and the Cybex logo are registered trademarks of Cybex International, Inc.
Arc Trainer
®
and its mark are registered trademarks of Cybex International, Inc.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183 • www.cybexinternational.com • techhelp@cybexintl.com
techpubs@cybexintl.com • Copyright © 2008, Cybex International, Inc. All rights reserved • 630A-326 A • March 2008
To Next Page
Loading...
