EasyManuals Logo

D-Link DSL-2740M Quick Installation Guide

D-Link DSL-2740M
8 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
TROUBLESHOOTING
SET-UP AND CONFIGURATION PROBLEMS
1. HOW DO I CONFIGURE MY DSL-2740M ROUTER WITHOUT THE CD, OR CHECK MY
WIRELESS NETWORK NAME (SSID) AND WIRELESS ENCRYPTION KEY?
- Connect your PC to the router using an Ethernet cable.
- Open a web browser and enter the address http://192.168.1.1
- The default username is ‘admin’. The default password is 'admin'.
- If you have changed the password and can not remember it, you will need to reset the router to
set the password back to 'admin'.
2. HOW DO I RESET MY DSL-2740M ROUTER TO FACTORY DEFAULT SETTINGS?
- Ensure the router is powered on.
- Press and hold the reset button on the rear of the device for 10 seconds.
Note: Resetting the router to factory default will erase the current conguration settings.
To re-congure your settings, log into the router as outlined in question 1, then follow the steps
in the 'SETUP YOUR MODEM ROUTER SECTION' of this QIG
3. HOW DO I ADD A NEW WIRELESS CLIENT OR PC IF I HAVE FORGOTTEN MY
WIRELESS NETWORK NAME (SSID) OR WIRELESS ENCRYPTION KEY?
- Every PC that needs to connect to the router wirelessly, you will need to ensure you use the
correct Wireless Network Name (SSID) and encryption key.
- Use the web based user interface (as described in question 1 above) to check or choose your
wireless settings.
- Make sure you write down these settings so that you can enter them into each wirelessly
connected PC. You will nd a dedicated area on the back of this document to record this
important information for future use.
4. WHY CAN I NOT GET AN INTERNET CONNECTION?
- Please contact your ISP to make sure the service has been enabled/connected by your ISP and
that your ISP username and password is correct.

Other manuals for D-Link DSL-2740M

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the D-Link DSL-2740M and is the answer not in the manual?

D-Link DSL-2740M Specifications

Ports & Interfaces IconPorts & Interfaces
RJ-11 ADSL port1
RJ-45 Ethernet ports4
Wireless InterfaceIEEE 802.11n/g/b
Wireless Specifications IconWireless Specifications
Wireless Bandwidth Rate IEEE 802.11b11, 5.5, 2, and 1 Mbps
Wireless Bandwidth Rate IEEE 802.11g54, 48, 36, 24, 18, 12, 9, and 6 Mbps
Wireless Bandwidth Rate IEEE 802.11n 20 MHz150, 130, 117, 104, 78, 52, 39, 26, 13 Mbps
Wireless Bandwidth Rate IEEE 802.11n 40 MHz300, 270, 243, 216, 162, 108, 81, 54, 27 Mbps
Operating Environment IconOperating Environment
Operating Humidity0% to 90% non-condensing
Non-Operating Humidity5% to 95% non-condensing
Operating Temperature0 to 40 °C (32 to 104 °F)
Non-Operating Temperature-20 to 65 °C (-4 to 149 °F)
Power IconPower
Input Voltage100~240 V AC (±20%), 50/60 Hz
Output Voltage12 V DC
Output Current0.5 A
Weight and Dimensions IconWeight and Dimensions
Dimensions160 x 120 x 25 mm (6.30 x 4.72 x 0.98 inches)
Weight205 grams (7.2 ounces)

Related product manuals