Daewoo DDC500 - User Manual

Questions and Answers

M
mendozasergioAug 20, 2025
Why does my Daewoo Digital Camera fail to trigger/miss flash?
- T
  Terri MyersAug 21, 2025
  If your Daewoo Digital Camera fails to trigger the flash, consider the following checks: * Verify the tube isn't offset and the tube wire has proper soldering and insulation. * Ensure the lampshade and copper foil contact is good, with infinite contact resistance between the lampshade and tube. * Confirm the big capacitor has sufficient soldering and normal voltage. * Check Q809 for breaks or soldering issues. * Inspect D809, C1210, and C838 for cold soldering or short-circuits. * Verify T802 isn't faulty and its soldering spots are secure.
C
Cameron ChambersAug 22, 2025
What to do if my Daewoo DDC500 Digital Camera TFT-LCD displays white image?
- K
  Karen SmithAug 22, 2025
  If your Daewoo Digital Camera's TFT-LCD shows a white image, check the following: * Ensure the LCD interface is fully inserted and properly soldered. * Verify that each power group (+5VL, +15VL, D3.3V, -7.5VL) of the LCD is normal. * Check the connection between the I/O board, the MCU connecting U model board, and the interface.
C
cheryl85Aug 25, 2025
What to do if Daewoo Digital Camera has USB no connection?
- I
  iadamsAug 25, 2025
  If your Daewoo Digital Camera has a USB connection issue, you can try the following: * Check the soldering and contact of camera base J2 and J4. * Verify J602 on the I/O board, the U model flex board, and their contact points are all in good condition. * Make sure your PC operating system is working correctly; note that systems older than Windows 2000 require driver program installation. * Ensure the external connection to the PC and the USB wire are functioning correctly.
J
Jamie AllenAug 27, 2025
Why does my Daewoo DDC500 fail to charge fully?
- C
  Crystal DavisAug 27, 2025
  If your Daewoo Digital Camera is failing to charge fully, verify the following: * Check that U805 and its surrounding components, including voltage, are normal. * Ensure Q808, D807, D808, T801, R847, and the large capacitor are functioning correctly. * Verify that R480, R841, R842, R843, and R844 are normal. * Inspect the large capacitor for any leaks or damage.
A
Ashley RiversAug 28, 2025
What to do if Daewoo DDC500 TFT-LCD is too dark?
- S
  Scott MannAug 28, 2025
  If the TFT-LCD on your Daewoo Digital Camera is too dark, check if the power, resistance, and audion of the LCD backlight circuit are working. Also, check if the LCD itself is OK.
B
Beverly McneilAug 29, 2025
How to fix aperture shift issue on Daewoo DDC500?
- S
  scottfoxAug 29, 2025
  To address an aperture shift issue on your Daewoo Digital Camera, check the lens connecting board for bad contact, cold soldering, or insufficient soldering. Also, check U7 on the MCU board and its surrounding components to ensure they are working correctly.
D
Dawn Wade MDAug 31, 2025
What to do if Daewoo DDC500 Digital Camera TV displays nothing?
- G
  Gail LopezAug 31, 2025
  If your Daewoo Digital Camera displays nothing on the TV, verify the TV interface is working correctly. Also, check if the camera base J4 soldering is OK, and ensure that J602 on the I/O board is OK, the U model flex board is OK, and the contact is OK.
A
April ThompsonSep 2, 2025
What to do if Daewoo DDC500 TV playback without sound/ noise/ voice too low/ too high?
- A
  annarichardsSep 2, 2025
  If TV playback from your Daewoo Digital Camera has sound issues like no sound, noise, or volume problems, first check the base TV interface. Then, verify the microphone wire soldering is secure. Finally, ensure J602 on the I/O board is OK, the U model flex board is OK, and the contact is OK.
C
Christian HinesSep 4, 2025
What to do if Daewoo Digital Camera power on without voice/ sound is abnormal?
- N
  nsheppardSep 4, 2025
  If your Daewoo Digital Camera powers on but the sound is missing or abnormal, check the following: * Ensure the speaker and lens flex board make good contact. * Verify the speaker is functioning correctly. * Check that the 9M747-7000 flex board and J302 on the shutter board connect well, and the flex board isn't broken. * Inspect the components surrounding U301 on the 9M747-3000. * Confirm the microphone wire soldering is secure and the microphone is working. * Consider updating the Full F/W.
M
Mary LamSep 5, 2025
What to do if Daewoo DDC500 TFT-LCD displays menu without image?
- M
  Michael SmithSep 6, 2025
  If your Daewoo Digital Camera's TFT-LCD displays the menu but no image, check if the lens shutter and aperture are opening correctly. Also, verify the CCD flex board installation is correct and the flex board isn't damaged. Additionally, check if the CCD and related components are OK, and ensure each voltage of the CCD is correct.