Why is my Daikin Air Conditioner not heating or cooling as expected?
Your Daikin Air Conditioner might not be heating or cooling as expected due to a few reasons. It could be due to incorrect connection of the electrical wires, in which case you should connect the electrical wires correctly. Another potential cause is gas leakage, so check for any gas leakage.
What to do if there's water leakage from my Daikin Air Conditioner?
If you notice water leakage from your Daikin Air Conditioner, it could be due to incomplete thermal insulation of the gas and liquid piping, or the indoor portions of the drain hose extension. Ensure the thermal insulation of the piping and the drain hose is complete. Another cause might be improperly connected drainage, so secure the drainage.
What to do if I suspect electrical leakage from my Daikin Air Conditioner?
If you suspect electrical leakage from your Daikin Air Conditioner, it's likely that the unit is not earthed correctly. Check and correct the connection of the earth wiring.
What to do if my Daikin ARXM71R2V1B unit does not function or shows burn damage?
If your Daikin Air Conditioner unit does not function or shows burn damage, this may be because the wiring was not performed in accordance with the specifications. Correct the wiring.
General| Category | Air Conditioner |
|---|---|
| Type | Split System |
| Cooling Capacity | 7.1 kW |
| Heating Capacity | 8.0 kW |
| Energy Efficiency Ratio (EER) | 3.21 |
| Seasonal Energy Efficiency Ratio (SEER) | 6.10 |
| Power Supply | 220-240V, 50Hz |
| Refrigerant | R32 |
| Outdoor Unit Weight | 48 kg |
| Outdoor Noise Level | 49 dB(A) |
Explains the meaning of various danger, warning, and caution symbols used in the manual.
Provides essential safety instructions for authorized installers during installation.
Details requirements and precautions for selecting a safe and suitable installation location.
Covers crucial safety measures when dealing with R32 refrigerant.
Outlines essential safety measures for electrical connections and wiring.
Highlights safety instructions and regulations for unit installation.
Specifies safety precautions for connecting refrigerant piping, including brazing.
Covers warnings and guidelines for safe electrical wiring practices.
This section details the purpose and content of the installer reference guide.
Overview of the outdoor unit packaging and essential handling instructions.
Step-by-step guide to safely unpack the outdoor unit and its accessories.
Details how to locate and read the identification label on the outdoor unit.
Guidelines for selecting and preparing a suitable location for unit installation.
Specifies required spacing around the outdoor unit for airflow and service.
Instructions and precautions for securely mounting the outdoor unit.
Guidance on ensuring proper drainage for condensation water.
Covers piping requirements, insulation, and length specifications.
Provides guidelines and precautions for connecting refrigerant pipes.
Details techniques for bending pipes and flaring pipe ends.
Instructions for leak testing and vacuum drying refrigerant piping.
Calculates additional refrigerant needed based on piping length.
Steps for charging additional refrigerant into the system.
Guidance on filling and affixing the fluorinated greenhouse gases label.
General precautions and guidelines for electrical wiring.
Details wire types, sizes, and tightening torques for connections.
Step-by-step instructions for connecting electrical wiring to the outdoor unit.
Final steps for insulating and fixing refrigerant piping and cables.
Instructions for correctly closing the outdoor unit cover.
Enables low outdoor temperature cooling for specific facilities.
Configures the unit for reduced power consumption in standby mode.
Essential safety measures before and during the commissioning process.
Lists items to verify before and during the commissioning phase.
Procedure for conducting a test run to ensure proper operation.
Ensures the user understands operation, maintenance, and problem-solving.
General safety guidelines to follow before performing maintenance.
Checklist for essential annual maintenance tasks on the outdoor unit.
Specific safety measures when servicing the unit's compressor.
Safety warnings and initial inspection steps before troubleshooting.
Guides on diagnosing and fixing issues based on unit symptoms.
Interpreting outdoor unit PCB LEDs for fault identification.
Safe refrigerant recovery process before unit disposal or relocation.
Methods to initiate and stop forced cooling for specific procedures.
Explains symbols, colors, and components used in wiring diagrams.
Illustrates refrigerant piping configurations for various unit models.
Provides definitions for key terms used throughout the manual.
To Next Page
