To Next PageTo Next Page
Need help?Do you have a question about the Daikin ATXF35E and is the answer not in the manual?
General| Type | Air conditioner indoor unit |
|---|---|
| Air filter | Yes |
| Multi-split | - |
| Product color | White |
| Timer duration (maximum) | 24 h |
| Air conditioner functions | Cooling, Heating |
| Cooling capacity in watts (nominal) | - W |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 Hz |
| Design load (cooling) | - kW |
| Hourly energy consumption (cooling) | - kWh |
| Indoor unit type | Wall-mountable |
| Indoor unit depth | 225 mm |
| Indoor unit width | 770 mm |
| Indoor unit height | 286 mm |
| Indoor unit weight | 8500 g |
| Indoor units quantity | 1 |
| Indoor unit package depth | 360 mm |
| Indoor unit package width | 830 mm |
| Indoor unit package height | 305 mm |
| Indoor unit package weight | 11000 g |
| Cooling airflow (indoor unit) | 690 m³/h |
| Heating airflow (indoor unit) | 714 m³/h |
| Indoor unit sound power level | 56 dB |
| Indoor unit noise level (low speed) | 27 dB |
| Indoor unit noise level (high speed) | 43 dB |
| Indoor unit fan speed (cooling, low speed) | 700 RPM |
| Indoor unit fan speed (heating, low speed) | 760 RPM |
| Indoor unit fan speed (cooling, high speed) | 1040 RPM |
| Indoor unit fan speed (heating, high speed) | 1140 RPM |
| Indoor unit fan speed (cooling, medium speed) | 870 RPM |
| Indoor unit fan speed (heating, medium speed) | 930 RPM |
| Outdoor unit noise level | - dB |
| Wi-Fi | No |
Provides information about the installation manual and its components.
Details the contents of the indoor unit packaging.
Instructions for removing accessories from the indoor unit packaging.
Provides an overview of the unit's system components and layout.
Specifies the safe and effective operating temperature and humidity ranges.
Guidelines for selecting and preparing the location for unit installation.
Specifies requirements for the indoor unit installation site.
Additional site requirements for outdoor units in cold climate conditions.
Instructions for safely opening the indoor unit casing.
Step-by-step guide to removing the front panel of the indoor unit.
Instructions for re-installing the front panel of the indoor unit.
Steps to remove the front grille from the indoor unit for maintenance or access.
Steps to re-install the front grille onto the indoor unit.
Procedure for accessing the electrical wiring compartment.
Instructions for opening the service cover of the indoor unit.
Guidelines for mounting the indoor unit onto the installation plate.
Steps for temporarily and permanently installing the mounting plate.
Procedure for drilling the necessary wall hole for pipes and cables.
Instructions for removing the pipe port cover for piping connections.
Guidance on ensuring proper drainage for condensation water.
Requirements and guidelines for preparing refrigerant piping.
Specifications for refrigerant piping material, diameter, and insulation.
Guidelines and procedures for connecting refrigerant piping.
Specific advice for connecting refrigerant pipes securely and preventing leaks.
Procedures for checking refrigerant piping for leaks.
Steps to perform a leak test on the refrigerant piping using nitrogen gas.
Details on recommended wiring components and their specifications.
Instructions for connecting the electrical wiring to the indoor unit.
Instructions for insulating drain piping, refrigerant piping, and interconnection cable.
Procedure for passing pipes and sealing the wall hole.
Steps for securely fixing the indoor unit onto the mounting plate.
Procedure to set different addresses for multiple indoor units in one room.
A checklist of items to verify before starting the commissioning process.
Procedure for performing a test run of the air conditioner.
Specific steps for performing a test run in cooling mode during winter.
Information on the location of the wiring diagram.
Legend explaining symbols used in the wiring diagram.
