What to do if an abnormal functioning happens during operation of Daikin FTXM35M2V1B?
If your Daikin Air Conditioner is functioning abnormally during operation, try turning the breaker off, then turning it back on. Afterward, try operating the air conditioner using the remote controller.
What to do if my Daikin FTXM35M2V1B does not turn on?
If your Daikin air conditioner isn't turning on, check the following: * Has a breaker tripped or a fuse blown? * Is there a power failure in your area? * Are the batteries correctly installed in the remote controller? * Is the timer setting correct?
Why is my Daikin Air Conditioner outdoor unit emitting water or steam?
The outdoor unit may emit water or steam for these reasons: * In HEAT operation: The frost on the outdoor unit melts into water or steam when the air conditioner is in defrost operation. * In COOL or DRY operation: Moisture in the air condenses into water on the cool surface of outdoor unit piping and drips.
Why is my Daikin Air Conditioner remote controller not working properly?
If your Daikin Air Conditioner's remote controller isn't working correctly, the batteries might be low. Try replacing them with new AAA.LR03 alkaline batteries.
Why is the cooling (heating) effect poor in my Daikin FTXM35M2V1B Air Conditioner?
If your Daikin Air Conditioner isn't providing sufficient cooling or heating, consider these potential causes: * Check if the air filters are clean. * Make sure nothing is blocking the air inlet or outlet of either the indoor or outdoor units. * Verify that the temperature setting is appropriate. * Ensure all windows and doors are closed. * Confirm the air flow rate and direction are properly set.
Why does mist come out of the indoor unit of my Daikin Air Conditioner?
If you notice mist coming out of the indoor unit of your Daikin Air Conditioner, it could be due to the air in the room being cooled into mist by the cold airflow during COOL operation or cooled by the heat exchanger and becoming mist during defrost operation.
Why Daikin FTXM35M2V1B remote controller does not work properly?
If your Daikin Air Conditioner remote controller isn't working, the batteries might be weak. Replace all batteries with new AAA.LR03 (alkaline) batteries.
Why does the indoor unit of my Daikin FTXM35M2V1B Air Conditioner gives out odour?
The odour from the indoor unit of your Daikin Air Conditioner can occur when smells from the room, furniture, or cigarettes are absorbed into the unit and discharged with the airflow. If this persists, it is recommended to have the indoor unit cleaned by a technician. Consult the service shop where you bought the air conditioner.
Why Daikin FTXM35M2V1B does not operate (OPERATION lamp is off)?
If your Daikin Air Conditioner does not operate and the OPERATION lamp is off, check the following: * Ensure that a breaker hasn’t turned off or a fuse hasn’t blown. * Confirm that there isn’t a power failure. * Verify that batteries are correctly installed in the remote controller. * Make sure the timer setting is correct.
What to do if my Daikin FTXM35M2V1B Air Conditioner operation stopped suddenly and the OPERATION lamp flashes?
If your Daikin Air Conditioner operation stopped suddenly and the OPERATION lamp is flashing, take these steps: * Ensure the air filters are clean and clean them if necessary. * Check for any obstructions blocking the air inlet or outlet of the indoor and outdoor units. * Turn the breaker off, remove any obstacles, and then turn it back on. Try operating the air conditioner with the remote controller again. If the lamp continues to flash, contact the service shop where you purchased the air conditioner.
General| Brand | Daikin |
|---|---|
| Model | FTXM35M2V1B |
| Category | Air Conditioner |
| Language | English |
Detects human movement for energy saving operation.
Read manual, intended use, warning classification.
Risks of fire, explosion, injury from misuse, hazardous substances.
Avoiding damage, proper installation, environmental considerations.
Identifies transmitter, receiver, LCD display, and main buttons.
Step-by-step guide to set the current time and day on the remote controller.
Explains the characteristics and best uses of AUTO, DRY, COOL, HEAT, and FAN modes.
How to modify the temperature for different operation modes.
Advice on efficient usage, including temperature settings, window coverings, and filter cleaning.
How to activate and control auto swing for upper/lower and right/left airflow.
Using 3-D airflow and setting flaps/louvers to a specific position.
Directs airflow for enhanced comfort during cooling/heating.
Detects presence for automatic energy saving.
How to activate COMFORT AIRFLOW and INTELLIGENT EYE operations via the remote.
Steps to deactivate these features and return to normal operation.
How to start and stop the POWERFUL operation.
Limits power consumption for efficiency and breaker protection.
How to activate ECONO and OUTDOOR UNIT QUIET modes using the remote.
Steps to deactivate these modes.
Instructions for programming and disabling the unit's turn-off timer.
Procedures for programming and disabling the unit's turn-on timer.
Overview of setting up to 4 timers per day for weekly scheduling.
Demonstrates setting different schedules for weekdays and weekends.
How to initiate the weekly timer setup process on the remote.
Choosing the day of the week and the program number for setting.
How to specify the time and temperature for each weekly timer reservation.
Finalizing the timer settings and confirmation.
Checks for power, errors, or abnormal functioning.
Addresses issues when the operation lamp flashes or is on.
Checks filters, obstructions, settings for reduced efficiency.
Symptoms requiring immediate professional attention.
A list of error codes and their meanings.
To Next Page
