Why Daikin Air Conditioner ON/OFF TIMER does not operate according to the settings?
If the ON/OFF TIMER on your Daikin Air Conditioner isn't working as expected, check whether the ON/OFF TIMER and the WEEKLY TIMER are set to the same time.
What to do if Daikin FVXS50KV1A HEAT operation stops suddenly and a flowing sound is heard?
If the HEAT operation on your Daikin Air Conditioner stops suddenly and you hear a flowing sound, wait for about 4 to 12 minutes.
Why is my Daikin FVXS50KV1A cooling effect poor?
Several factors can affect the cooling performance of your Daikin Air Conditioner. Please check the following: * Ensure the air filter is clean. * Verify that nothing is blocking the air inlet or outlet of both the indoor and outdoor units. * Confirm that the temperature setting is appropriate for your needs. * Make sure all windows and doors are closed properly. * Check that the airflow rate and air direction are set correctly.
Why my Daikin Air Conditioner remote controller is not working properly?
If your Daikin Air Conditioner remote controller isn't displaying signals, has low sensitivity, a low contrast display, or the display is out of control, the batteries may be dying or the remote controller may be malfunctioning. Try replacing all batteries with new AAA alkaline batteries. If a reset button is available, press it after replacing the batteries.
What to do if Daikin FVXS50KV1A malfunctions during operation?
If your Daikin Air Conditioner is malfunctioning during operation, it might be due to interference from lightning or radio waves. To resolve this, turn the breaker off, then turn it back on, and try operating the air conditioner using the remote controller.
Why hot air does not flow out soon after the start of HEAT operation in Daikin FVXS50KV1A Air Conditioner?
If hot air doesn't flow out soon after starting the HEAT operation on your Daikin Air Conditioner, allow 1 to 4 minutes for it to begin.
Why Daikin Air Conditioner operation does not start soon?
If your Daikin Air Conditioner operation doesn't start immediately, wait for about 3 minutes.
What to do if my Daikin Air Conditioner operation stops suddenly and the OPERATION lamp flashes?
If your Daikin Air Conditioner stops suddenly and the OPERATION lamp is flashing, try the following steps: 1. Clean the air filter. 2. Turn the breaker off, remove any obstacles, and turn it back on. 3. If the lamp continues to flash, you should contact the service shop where you purchased the air conditioner. 4. Ensure all indoor units are set to the same operation mode. If in AUTO mode, temporarily set all indoor units to COOL or HEAT.
How to fix Daikin Air Conditioner ON/OFF TIMER if it does not operate according to the settings?
If the ON/OFF TIMER on your Daikin Air Conditioner isn't working as set, try changing or disabling the settings in the WEEKLY TIMER.
Why is the ON/OFF TIMER on my Daikin FVXS50KV1A not working as expected?
Check if the ON/OFF TIMER and the WEEKLY TIMER are set to the same time on your Daikin Air Conditioner. If they are, change or disable the settings in the WEEKLY TIMER.
General| Type | Floor Standing |
|---|---|
| Cooling Capacity | 5.0 kW |
| Heating Capacity | 5.8 kW |
| Refrigerant | R32 |
| Indoor Unit Dimensions (W x H x D) | 600 x 700 x 210 mm |
| Outdoor Unit Weight | 34 kg |
| Energy Efficiency Ratio (Cooling) | 3.21 |
| Outdoor Unit Noise Level | 48 dB(A) |
| Power Supply | 220-240V, 50Hz |
Keep manual accessible, read precautions, understand WARNING/CAUTION symbols for safe operation.
Avoid harmful gases, direct air exposure, placing objects in outlets, and using flammable sprays near the unit.
Operate with dry hands, ensure proper earthing, and install an earth leakage circuit breaker.
Use unit for intended purpose, avoid direct airflow on plants/animals, and keep naked flames away.
Consult dealer for environments like oily areas, salty coasts, or where sulphide gas occurs.
Choose installation locations to minimize noise and vibration annoyance to neighbors.
Ensure a separate power circuit dedicated to the air conditioner for safe operation.
Identifies filters, louvers, flap, display panel, and signal receiver on the indoor unit.
Details air inlet/outlet, refrigerant piping, drain hose, and earth terminal of the outdoor unit.
Identifies transmitter, LCD display, and various buttons on the remote controller.
Instructions for inserting AAA batteries and notes on battery life and replacement.
Guidance on selecting a location and fixing the remote controller holder to the wall.
Step-by-step guide using CLOCK and SELECT buttons to set the current time and day.
Recommendations for moderate temperature settings, window coverings, and filter cleaning.
Recommended settings and usage conditions for COOL, HEAT, and DRY modes.
Instructions for using MODE and ON/OFF buttons to start, stop, and select modes.
How to adjust the temperature using the TEMP Up/Down buttons on the remote.
Using the FAN button to select different airflow levels for cooling/heating.
Specific notes for HEAT, COOL, DRY, AUTO, and FAN operations.
Using the SWING button to control the horizontal airflow direction.
Manual adjustment of vertical louvers for airflow direction.
Configuring the air outlet switch for different blowing patterns in various modes.
Maximizes cooling/heating effect by increasing outdoor unit capacity and airflow.
How to stop the Powerful Operation mode by pressing the button again.
Lowers outdoor unit noise by adjusting frequency and fan speed, activated by QUIET button.
How to disable the Outdoor Unit Quiet Operation by pressing the QUIET button again.
Enables efficient operation by limiting maximum power consumption, activated by ECONO button.
How to deactivate Econo Operation by pressing the ECONO button again.
Setting and cancelling the timer to automatically switch the unit off.
Setting and cancelling the timer to automatically switch the unit on.
Example of setting both ON and OFF timers for sequential operation.
Setting up to 4 timer programs per day for weekly scheduling.
Detailed steps for setting day, time, temperature, and ON/OFF status.
Copying programmed settings from one day to another for easier scheduling.
How to check programmed timer settings and their details.
Turning the weekly timer function off temporarily.
Removing specific day's timer settings from the weekly program.
Clearing all programmed timer settings from the weekly schedule.
Wiping the indoor unit and remote controller with a dry soft cloth.
Instructions for opening, removing, cleaning, and reattaching the front panel.
Procedure for cleaning or replacing the air filter with water or vacuum.
Guidance on washing and replacing the titanium apatite photocatalytic air-purifying filter.
Explanations for common cases that are not actual troubles.
A checklist to help diagnose and resolve common operating problems.
List of error codes displayed by the remote controller for fault diagnosis.
When to call the service shop and recommendations for periodical maintenance.
To Next Page
