• Indoor Units • Round Flow Cassette • FXFQ-P9VEB
•VRV
®
Systems • Indoor Units
12
5 Dimensional drawing & centre of gravity
5 - 1 Dimensional drawing for standard panel
FXFQ20,25,32,40,50,63P9
3TW28834-1B
Nr Name Description
1Liquid pipe connection ø A flare connection
2Gas pipe connection ø B flare connection
3 Drain pipe connection VP25 (O.D. ø 32 /I.D. ø 25)
4 Power supply entry hole
5 Transmission wiring entry hole
6 Air discharge opening
7 Air suction grille
8 Corner decoration cover
9 Drain hose O.D. ø 32 /I.D. ø 26
10 Knock out hole
Piping side
Drain side
see note 3
300 or less
860-910 (Ceiling opening)
710 (Suspension position
950
420
420
780 (Suspension position
860-910 (Ceiling opening)
SEE NOTE 4
175
850
Adjustable (0-675)
125
55
840
340
280
330
165
214
55
55 55
35
SEE NOTE
4
SEE NOTE
4
840
130
35
1500 or more
(installation space)
1500 or more
2000 or more
4000 or more
EXTERNAL
SURFACE
LIGHT
VENTILATOR OTHER UNIT
1500mm
or more (*)
1500mm
or more (*)
1500mm
or more (*)
200mm
or more
1500mm
or more (*)
200mm
or more
(*) In case a discharge opening is closed with the ‘sealing member’ option,
the distance of 1500mm can be reduced to 500mm on the closed side.
Hanging bolt
4 x M8~M10
MODEL A B
FXFQ20-50P9 6.35 12.7
FXFQ63P9 9.52 15.9
213
139
7
5
VIEW B
VIEW A
SEE NOTE
6
950
50 204
40
10
NOTES
1 Location of the nameplates
- Unit body: on the control box cover.
-
Decoration panel: on the panel frame at the motor side under the corner cover
2When installing an optional accessory, refer to the installation drawings.
- For the fresh air intake kit an inspection port is necessary
3
In case of using an infrared remote control, this position will be a signal
receiver. Refer to the drawing of the infrared remote control for more detail.
4 Make sure the spacing between the ceiling and the cassette is no more
than 35mm. MAX ceiling opening: 910mm.
5 When the conditions exceed 30°C and RH 80% in the ceiling or fresh air
is inducted into the ceiling, an additional insulation is required
(polyethylene foam, thickness 10mm or more).
6 Please respect the distances as shown on the figure
FXFQ80,100P9
3TW28894-1B
Piping side
Drain side
see note 3
300 or less
860-910 (Ceiling opening)
710 (Suspension position
950
420
420
780 (Suspension position
860-910 (Ceiling opening)
SEE NOTE 4
175
850
Adjustable (0-675)
125
55
840
340
280
330
165
214
55
55 55
35
SEE NOTE
4
SEE NOTE
4
840
130
35
1500 or more
(installation space)
1500 or more
2000 or more
4000 or more
EXTERNAL
SURFACE
LIGHT
VENTILATOR OTHER UNIT
1500mm
or more (*)
1500mm
or more (*)
1500mm
or more (*)
200mm
or more
1500mm
or more (*)
200mm
or more
(*) In case a discharge opening is closed with the ‘sealing member’ option,
the distance of 1500mm can be reduced to 500mm on the closed side.
Hanging bolt
4 x M8~M10
213
139
7
5
VIEW B
VIEW A
SEE NOTE
6
950
50 204
40
10
NOTES
1 Location of the nameplates
- Unit body: on the control box cover.
-
Decoration panel: on the panel frame at the motor side under the corner cover
2When installing an optional accessory, refer to the installation drawings.
- For the fresh air intake kit an inspection port is necessary
3
In case of using an infrared remote control, this position will be a signal
receiver. Refer to the drawing of the infrared remote control for more detail.
4 Make sure the spacing between the ceiling and the cassette is no more
than 35mm. MAX ceiling opening: 910mm.
5 When the conditions exceed 30°C and RH 80% in the ceiling or fresh air
is inducted into the ceiling, an additional insulation is required
(polyethylene foam, thickness 10mm or more).
6 Please respect the distances as shown on the figure
Nr Name Description
1Liquid pipe connection ø 9.52 flare connection
2Gas pipe connection ø 15.90 flare connection
3 Drain pipe connection VP25 (O.D. ø 32 /I.D. ø 25)
4 Power supply entry hole
5 Transmission wiring entry hole
6 Air discharge opening
7 Air suction grille
8 Corner decoration cover
9 Drain hose O.D. ø 32 /I.D. ø 26
10 Knock out hole
To Next Page
Loading...
