To Next PageTo Next PageWhat to do if my Daitsu DS-18UIAK unit can not be started up?
If your Daitsu Air Conditioner unit won't start, check the following: Is the power cut off? Is the power plug loose? Is the circuit protection device tripped off? Is the voltage higher or lower than normal? Is the TIMER correctly used?
Why is my Daitsu DS-18UIAK indoor unit not blowing air?
If your Daitsu Air Conditioner indoor unit is not blowing air in HEAT mode, it may be because the temperature of the indoor heat exchanger is very low, which stops airflow to prevent cold air for up to 2 minutes. Also, in HEAT mode, frost may form on the outdoor heat exchanger when the outdoor temperature is low or humidity is high. The unit will defrost automatically, and the indoor unit will stop blowing air for 3-12 minutes. During defrosting, water or vapour may be emitted. In DRY mode, the indoor fan may stop blowing air for 3-12 minutes to prevent condensate from being vaporized again.
How to fix Daitsu DS-18UIAK remote controller that is not working?
If your Daitsu Air Conditioner remote isn't working, try these steps: First, check for any magnetic or electrical interference near the unit; if present, unplug the unit and plug it back in. Then, ensure the remote is within its operating range and not obstructed. Finally, check the batteries and replace them if needed, and inspect the remote for any damage.
What to do for C5 Malfunction of connector jumper on Daitsu Air Conditioner?
If you're getting a C5 error (malfunction of connector jumper) on your Daitsu Air Conditioner, check if the connector jumper contacts properly. If replacing the PCB, transfer the old one to the new PCB.
What to do for F2 Malfunction of evaporator temperature sensor on Daitsu DS-18UIAK Air Conditioner?
If you're seeing an F2 error (malfunction of evaporator temperature sensor) on your Daitsu Air Conditioner, check if the evaporator temperature sensor is properly connected.
What to do for F1 Malfunction of indoor ambient temperature sensor on Daitsu DS-18UIAK?
If you're seeing an F1 error (malfunction of indoor ambient temperature sensor) on your Daitsu Air Conditioner, check if the indoor room temperature sensor is properly connected.
What to do for H6 Indoor fan block error on Daitsu Air Conditioner?
If you're getting an H6 error (indoor fan block) on your Daitsu Air Conditioner, check if the terminal of the indoor motor is properly connected. If the problem persists, the fan motor or the indoor board may need to be replaced if disabled.
Why Daitsu Air Conditioner indoor unit can not blow air?
If the indoor unit of your Daitsu Air Conditioner isn't blowing air, it could be due to the following reasons: In HEAT mode, airflow stops temporarily to prevent cold air when the indoor heat exchanger temperature is very low (within 2 minutes). Also in HEAT mode, if the outdoor temperature is low or humidity is high, frost may form on the outdoor heat exchanger, causing the unit to defrost automatically and stop airflow for 3-12 minutes. During defrosting, water or vapor may be emitted. In DRY mode, the fan may stop for 3-12 minutes to prevent condensate vaporization.
Why is my Daitsu Air Conditioner outdoor unit leaking water?
Water leakage from the outdoor unit of your Daitsu Air Conditioner can occur during cooling operation due to condensate around pipes and joints. It can also happen during defrosting as thaw water flows out or during heating when water drips from the heat exchanger.
Why is my Daitsu DS-18UIAK indoor unit making noise?
The noise from your Daitsu Air Conditioner's indoor unit could be due to the fan or compressor relay switching on or off. Also, a sound of refrigerant flowing in reverse may occur when defrosting starts or stops.
Details the functions of basic remote control buttons like SLEEP, FAN, CLOCK, ON/OFF, and MODE.
Explains advanced functions such as temperature adjustment, X-FAN, and TURBO mode on the remote.
Addresses common problems like unit non-operation, odors, water noise, mist emission, and cracking sounds.
Covers unit startup, performance, remote control, and water leakage problems.
Addresses issues with indoor airflow, sensor malfunctions, and specific error codes like C5, F1, F2, H6.
Provides general advice on selecting an appropriate installation site, avoiding hazards and unsuitable environments.
Details specific site requirements for both the indoor and outdoor units for optimal performance and safety.
Outlines crucial safety measures related to electrical connections, grounding, and circuit protection.
Explains the importance of proper earthing, the designated earthing wire, and connection points.
General| Brand | Daitsu |
|---|---|
| Model | DS-18UIAK |
| Category | Air Conditioner |
| Language | English |
