EasyManua.ls Logo

Daktronics BB-2140 - User Manual

Default Icon
38 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
201 Daktronics Drive
Brookings, SD 57006-5128
www.daktronics.com/support
800.325.8766
TRANSPARENT SHOT CLOCKS
DISPLAY MANUAL
P1322
ED-15168
Rev 08
12 June 2018
Models
BB-2140 BB-2150 (NBA only)
BB-2141 BB-2151 (NBA only)

Table of Contents

Questions and Answers

  • J
    James Smith Jr.Aug 7, 2025
    How to troubleshoot a Daktronics BB-2140 Clock when the display and console don't work?
    • B
      Brandon GrahamAug 8, 2025
      If the Daktronics Clock display and console aren't working, start by checking the main circuit breaker for the display to ensure it's on. Also, verify that the control enclosure is receiving either 120 or 240 VAC power. For the console, make sure it's properly plugged into a 120 or 240 VAC power supply. If possible, test the console by exchanging it with a known working one, entering the correct sport code and radio settings to see if it resolves the issue. Replace the console if necessary.
  • M
    Marissa RandallAug 11, 2025
    What to do if Daktronics BB-2140 Clock display digits don't light, but the console works?
    • M
      Mary GutierrezAug 11, 2025
      If the Daktronics Clock console works but the display digits do not light up, consider the following: * Check that the control enclosure is receiving 120 or 240 VAC power. * Verify that both the console and display antennas are securely tightened and in a vertical position. * Ensure the console is 20–500' (6–152 m) away from the display. Check that the green POWER and amber RADIO IN RANGE indicators on the radio receiver in the display light up when the control console is powered on. Move the console 20–30' (6–9 m) from the display and test again. Also, check that the red DS3 LED on the driver lights up when sending commands from the controller. If a radio signal issue is suspected, replacing the radio receiver might be necessary.
  • M
    Mary HarrisonAug 16, 2025
    Why do some LEDs not light or blink on my Daktronics BB-2140 display?
    • A
      Alicia RhodesAug 16, 2025
      If your Daktronics Clock display works, but some LEDs aren't lighting up or are blinking, verify the connector on the back of the digit circuit board is secure. If the connection is good, try exchanging the digit or driver with a working one of the same part number to see if that resolves the issue. Replace if necessary.
  • B
    Brandon MoralesAug 20, 2025
    Why are Daktronics Clock display digits lit but in the wrong order?
    • W
      wardbrandyAug 20, 2025
      If the digits on your Daktronics Clock light up but are not in the correct order, ensure the correct sport code is being used for your display model. Also, verify that all drivers are set to the correct address.
  • R
    Ronald ThomasAug 25, 2025
    What to do if Daktronics Clock digits light, console works, but nothing displays?
    • C
      Cody HolderAug 26, 2025
      If the digits light up and the console works, but nothing is displayed on your Daktronics Clock, check that the red DS3 LED on the driver lights up when sending commands from the controller.
  • N
    nicoleweaverAug 28, 2025
    Why are some LEDs always on in my Daktronics BB-2140 display?
    • K
      Kenneth ElliottAug 28, 2025
      If your Daktronics Clock display is working, but some LEDs are always on, exchange the digit with a working one of the same part number to verify if there's a short in the digit circuit. Replace if necessary.
  • M
    matthewroachSep 2, 2025
    What causes one section of digits to not light on a Daktronics BB-2140 Clock?
    • R
      Robert KochSep 3, 2025
      If your Daktronics Clock display works, but one section of digits does not light up, exchange the transformer with a working one of the same part number to verify the problem. Replace if necessary.

Daktronics BB-2140 Specifications

General IconGeneral
BrandDaktronics
ModelBB-2140
CategoryClock
LanguageEnglish