Dancing Wings Hobby Fokker Dr.I User Manual

A
B
C
E F
G
H
D2
D1
D3
I
J
T
K
L
M
S
R1
R2
Q
P1
P2
N O
P1
A
Fokker Dr.I
Instruction Manual
1.Install landing gear bracket P1, embed the bracket
into the prefrmed groove,lock it with self-tapping screw
and M spacer.
2.Install landing gear aileron and wheels.
3.Plug the middle wings into each other with carbon
rod,glue the joint.
4.Plug the middle wing's bolt into the fuselage, then
lock the wing with self-tapping screw.
5.Plug the upper wings into each other with carbon
rod, glue the joint.
6.Install wing bracket in the back of the upper wing,
lock it with self-tapping screw.
7.Use self-tapping screw to lock the other end of
bracket on the fuselage.
8.Install wing's support rods as shown.
9.Plug lower wings into each other with carbon rod,
glue the joint.
10.Use self-tapping screw to lock the lower wing on
the fuselage.
11.Support rods connect the lower wing, adjust the
space among the three wings and fasten them.
12.Install motor board, and install the emulational
engine on the motor board.Install emulational
machine gun on the middle wing. (Don't stick the
motor board on the fuselage at this moment, please
stick the motor board on the fuselage after finishing
the motor installation.)
13.Install the cowling, fasten the edge with 3pcs
self-tapping screws.
14.Install horizontal tail, connect with fuselage groove,and
fix it with glue.Connect the vertical tail to the tail of fuselage
with paper hinge, and make the vertical tail swing freely.
C
T
P2
T
Lock the wheels
P2
P1
Fasten it with screw
Short
Long
R2
R1
D1
D3
D2
O
I
Q
H
B
Specification
Wingspan：770mm
Length：630mm
Net weight：≈650g
Suggested Equipment
Motor： 2212 800-1000KV
ESC：20A
Servo：2.5g *2 & 5g *2
Propeller：7-8 inch
Battery：2-3S 1300-1800mAh
Radio≥3CH
A:Fuselage B:Vertical tail C:Landing gear aileron D1-3:Wing
E:Screw set, quick connector, wheel lock
F:Emulational machine gun G:Sled H:Horizontal tail
I:Emulational engine J:Rudder angle K:Paper hinge
L:Carbon rod M:Spacer N:Wheel bracket O:Motor board
P1-2:Landing gear steel wire Q:Cowling R1-2:Wing bracket
S:Sticker
T:Wheel
Fasten it with screw
Here M spacer
is for cabin
cover,you can
open and close
it freely.

Dancing Wings Hobby Fokker Dr.I Specifications

General

Wingspan	800mm
Length	650mm
Material	Balsa wood
Flight Time	8-10 minutes
Servo	9g x 4
Type	RC Airplane

Summary

Fokker Dr.I Specifications and Components

Aircraft Specifications

Details the aircraft's wingspan, length, net weight, and recommended components.

Component Identification

Lists and identifies various parts of the model, such as fuselage, wings, and hardware.

Fokker Dr.I Assembly Instructions

Landing Gear Installation

Install the landing gear bracket, aileron, and wheels securely.

Wing Assembly and Attachment

Join wing sections with carbon rods, glue, attach brackets, and secure to fuselage.

Motor and Engine Installation

Install the motor board and emulational engine, then mount the cowling.

Tail Section Assembly

Attach the horizontal tail and connect the vertical tail with a paper hinge.

Fokker Dr.I System and Control Setup

Control Surface and Servo Linkage

Connect rudder and elevator angles, servos, and steel wire pulling rods.

Power System and Propeller Mounting

Install the motor on the board, secure it to the fuselage, and fasten the propeller.

Center of Gravity (CG) Adjustment

Locate and adjust the Center of Gravity (CG) for optimal flight.

Final Touches and Static Display

Apply stickers and prepare the model for static display on a wooden box.

Safety Precautions and Warnings

General Safety Guidelines

Provides essential safety advice for operating the model, including distance and environment.

Handling and Storage

Advises on proper handling of chemicals, small parts, and avoiding water exposure.