EasyManua.ls Logo

Danze D112000BT User Manual

Danze D112000BT
6 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Before Your Installation
Antes de Instalar
Avant líinstallation
Tools You Will Need
Herramientas Necesarias
Outils dont vous aurez besoin
SAFETY TIPS
• Caution: If you use soldering for the installation of this faucet, the seat cartridges and
washers will have to be removed before turning on the flame. Damage to the cartridge and
seats will occur if left intact while soldering and will result in the warranty being void on
these parts.
• Cover your drain to avoid loosing parts.
CONSEJOS DE SEGURIDAD
Advertencia: Si usa soldadura para la instalación de este grifo, remueva los componentes
internos y las arandelas antes de encender la llama. Si no se remueven, estas piezas se
dañarán durante la soldadura, lo que resultará en la anulación de la garantía para estas
piezas.
• Tape la boca del desagüe para prevenir la pérdida de piezas pequeñas.
CONSEILS DE SÉCURITÉ
Attention: Si vous effectuez l’installation de ce robinet par soudage, vous devez enlever les
sièges de cartouche et les rondelles avant d’allumer la flamme. La cartouche et les sièges
seront endommagées s’ils sont laissés en place lors du soudage, entraînant ainsi l’annulation
de la garantie de ces pièces.
• Couvrez le drain à fin de ne pas perdre de pièces.
Hacksaw
Sierra para metales
Scie à métaux
Phillips screwdriver
Destornillador cruciforme
Tournevis Phillips
Adjustable wrench
Llave ajustable
Clé à molette
Pipe tape
Cinta selladora para rosca
Ruban pour tuyau
Groove joint plier
Pinzas ajustables
Pince multiprise
Check to make sure you have the following parts indicated below:
Verifique que tenga todas las partes indicadas:
Vérifier pour vous assurer que vous possédez les pièces au bas:
Need Help? Please call our toll-free Customer service line at 1-888-328-2383 for additional assistance or service.
Requiere asistencia? Favor llamar a nuestro servicio a clientes sin costo al 1-888-328-2383 para asistencia adicional o servicio.
Besoin d’aide? Veuillez communiquer avec notre service à la clientèle au numéro sans frais 1-888-328-2383 pour obtenir du
service ou de l’aide additionnels.
Tub and Shower Faucet Rough-in Valve Assembly
Válvula interior de grifo para bañera y ducha
Ensemble de robinet de robinetterie brute pour bain et douche
D112000BT
D113000BT
D115000BT
Question and Answer IconNeed help?

Do you have a question about the Danze D112000BT and is the answer not in the manual?

Danze D112000BT Specifications

General IconGeneral
BrandDanze
ModelD112000BT
CategoryKitchen & Bath Fixtures
LanguageEnglish

Summary

Safety Tips

Soldering Caution

Remove seat cartridges and washers before soldering to prevent damage and voided warranty.

Connect Water Supply Piping

Threaded Connections

Connect water supply tube using pipe tape on threaded ends.

Soldering Connections

Solder water supply tube to valve body, cautioning against overheating.

Standard Shower Wall Construction

Shower Only Installation

Tub Filler Installation

Tub and Shower Faucet Installation

Connect Shower and Tub Piping

Connect shower piping to top port and tub filler piping to bottom port.

Thin Wall Construction

Temperature Limiting Device

Normal Installation Setup

Ensure dimple on valve stem points upward for hot left, cold right installation.

Reverse Installation Setup

For hot right, cold left, rotate stem 180 degrees so dimple points downward.

Adjust Temperature Limiting

Rotate Stem and Adjust

Rotate valve stem to open, adjust temperature using a thermometer.

Related product manuals