Need help?Do you have a question about the Daytona Anima 190F and is the answer not in the manual?
Lists failures not considered product defects, including overheating and improper parts.
States the customer's responsibility for operating and maintaining products as specified in the manual.
Explains how to get services and the scope of DAYTONA Corp. JAPAN's service responsibility.
Details the warp limit for the cylinder head component.
Specifies bore size and out of round limit for the cylinder.
Provides cam dimensions (H and D) for intake and exhaust valves.
Lists timing chain specs: number of links and adjustment method.
Specifies valve clearance (cold) for intake and exhaust.
Details valve dimensions: head diameter, face width, seat width, and margin thickness.
Specifies the free length for intake and exhaust valve springs.
Provides piston specs: clearance, size, measuring point, off-set, pin bore, and diameter.
Details specs for top/second rings: dimensions, end gap, and side clearance.
Specifies dimensions and end gap for the oil ring.
Lists crankshaft specs: width, runout limit, side clearance, and free play.
Provides clutch specs: plate thickness, quantities, warp limit, and spring length.
Specifies intervals for replacing and inspecting engine oil.
Details intervals for checking valve clearances and inspecting/replacing valves.
Specifies intervals for inspecting and replacing valve springs.
Details intervals for inspecting and replacing camshafts.
Outlines intervals for inspecting and replacing timing chain and sprockets.
Specifies intervals for inspecting, cleaning, and replacing the piston.
Details intervals for inspecting and replacing piston rings.
Specifies intervals for inspecting and replacing the piston pin.
Details intervals for inspecting, cleaning, and replacing the cylinder head.
Specifies intervals for inspecting, cleaning, and replacing the cylinder.
Outlines intervals for inspecting, adjusting, and replacing the clutch.
Details intervals for inspecting and replacing transmission components.
Specifies intervals for inspecting shift fork, cam, and guide bar.
Details intervals for retightening the rotor nut.
Specifies intervals for inspecting and aligning the crank.
Outlines intervals for inspecting, adjusting, and cleaning the carburetor.
Details intervals for inspecting, cleaning, and replacing the spark plug.
Specifies intervals for checking oil cooling system hoses and replacing gaskets.
Details intervals for cleaning, lubricating, and replacing the air filter.
Specifies intervals for replacing the oil filter.
Details intervals for cleaning the oil strainer.
Explains how to check the engine oil level through the sight glass.
Discusses carburetor sensitivity, handling, and atmospheric condition settings.
Illustrates how jets and needles affect throttle valve opening.
Provides recommended settings for KEIHIN PWK33 carburetor based on conditions.
Offers recommended settings for KEIHIN PE28 carburetor based on conditions.
Details wire color codes and their corresponding ignition timing settings (Reduce/Advance).
Lists wire color codes and their corresponding rev limiter settings (RPM ranges).
Warns about engine damage from overheating and recommends oil coolers/gauges.
Details Daytona oil cooler kits (7-Core and 10-Core) and mount bracket requirements.
Describes Daytona gauges and fittings compatible with oil coolers.
Details sensor fittings for oil coolers and oil drain bolt applications.
Introduces a reinforced clutch friction disc manufactured by FCC JAPAN.
Presents the Keihin PWK33 carburetor with throttle valve #6.0 as an optional part.
Lists jet needles for PWK33, including part numbers and specifications.
Details Main Jet Sets for Keihin carburetors, with various sizes available.
Lists Slow Jet Sets for Keihin PE & PWK carburetors with air bleed type.
Presents the Keihin PE28 carburetor with throttle valve #3.0 as an optional part.
Details Main Jet Sets for Keihin carburetors, with various sizes available.
Lists Slow Jet Sets for Keihin PE & PWK carburetors with air bleed type.
Lists various Daytona Jet Needles with part numbers, taper angles, and specifications.
Details Daytona throttle valves for PE28 carburetors, with different sizes available.
Lists parts for the cylinder head and cylinder assembly.
Lists parts for the valve mechanism, including rocker arms, camshaft, and valves.
Lists parts for the piston and crankshaft assembly.
Lists parts for the crankcase, including bolts, covers, and gaskets.
Lists parts for the clutch assembly, including bearings and clutch components.
Lists parts for the clutch cover, including bolts, gaskets, and seals.
Lists parts for the gearbox, including bearings, gears, and oil seals.
Lists parts for the gearbox mechanism, including shift drum and lever.
Lists parts for the oil pump, including bolts, gasket, and the pump assembly.
Lists the part for the kick starter assembly.
Lists parts for the generator, including bolts, CDI box, ignition coil, and stator.
To Next Page
General
