How to fix hard-disk drive configuration error on Dell OptiPlex 5080 Desktop?
To fix a hard-disk drive configuration error on your Dell Desktop, shut down the computer, remove the hard drive, and boot the computer from an optical drive. Then, shut down the computer, reinstall the hard drive, and restart the computer. Run the Hard Disk Drive tests in Dell Diagnostics.
How to fix 'Operating System not found' on Dell OptiPlex 5080?
If you receive an 'Operating System not found' error on your Dell Desktop, reinstall the operating system. If the problem continues, no answer.
What to do if I get 'Bad command or file name' error on Dell Desktop?
If you encounter a 'Bad command or file name' error on your Dell Desktop, ensure that you have spelled the command correctly, put spaces in the proper place, and used the correct path name.
How to resolve 'Invalid configuration information' on Dell Desktop?
To resolve the 'Invalid configuration information' error on your Dell Desktop, correct the appropriate options in the system setup program.
What to do if no boot device available on Dell Desktop?
If your Dell Desktop displays 'No boot device available', and the hard drive is your boot device, ensure that the drive is installed, properly seated, and partitioned as a boot device.
How to troubleshoot memory/RAM failure on Dell OptiPlex 5080 Desktop?
To troubleshoot a memory/RAM failure on your Dell Desktop, reset the memory module. If the problem persists, replace the memory module.
What to do if 'Disk C failed initialization' on Dell OptiPlex 5080 Desktop?
If your Dell Desktop shows 'Disk C failed initialization', run the hard drive tests in Dell Diagnostics.
How to diagnose a CPU failure on a Dell OptiPlex 5080?
To diagnose a CPU failure on your Dell Desktop, run the Intel CPU diagnostics tools. If the problem persists, replace the system board.
How do I fix a GATE A20 failure on my Dell OptiPlex 5080?
To fix a GATE A20 failure on your Dell Desktop, reinstall the memory module or, if necessary, replace it.
What to do if 'The file being copied is too large for the destination drive' on Dell OptiPlex 5080?
If you receive the error 'The file being copied is too large for the destination drive' on your Dell Desktop, try copying the file to a different disk or use a larger capacity disk.
General| Processor cache | 16 MB |
|---|---|
| Processor cores | 8 |
| Processor family | Intel® Core™ i7 |
| Processor frequency | 2 GHz |
| Processor cache type | Smart Cache |
| Configurable TDP-down | 25 W |
| Processor manufacturer | Intel |
| Processor boost frequency | 4.5 GHz |
| Number of processors installed | 1 |
| Configurable TDP-down frequency | 1.3 GHz |
| Memory slots | 2x SO-DIMM |
| Internal memory | 16 GB |
| Memory clock speed | 2666 MHz |
| Internal memory type | DDR4-SDRAM |
| Maximum internal memory | 64 GB |
| SSD capacity | The Solid State Drive's storage capacity in Gigabytes. |
| SSD interface | PCI Express |
| Storage media | SSD |
| SSD form factor | M.2 |
| Optical drive type | No |
| Total storage capacity | 256 GB |
| On-board graphics card | Yes |
| Discrete graphics card model | Not available |
| On-board graphics card model | Intel® UHD Graphics 630 |
| Wi-Fi standards | 802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac), Wi-Fi 6 (802.11ax) |
| Bluetooth version | 5.1 |
| Cabling technology | 10/100/1000Base-T(X) |
| Top Wi-Fi standard | Wi-Fi 6 (802.11ax) |
| WLAN controller model | Intel Wi-Fi 6 AX201 |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| DisplayPort version | 1.4 |
| USB 2.0 ports quantity | 0 |
| USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity | 5 |
| Chassis type | MFF |
| Product color | Black |
| Placement supported | Horizontal/Vertical |
| Audio chip | Realtek ALC3246 |
| Audio system | High Definition Audio |
| Product type | Mini PC |
| Motherboard chipset | Intel Q470 |
| Trusted Platform Module (TPM) | - |
| Operating system architecture | 64-bit |
| Power supply | 90 W |
| Power supply input voltage | 100 - 240 V |
| Power supply input frequency | 50 - 60 Hz |
| Operating altitude | 0 - 3048 m |
| Non-operating shock | 105 G |
| Operating vibration | 0.26 G |
| Non-operating altitude | 0 - 10668 m |
| Non-operating vibration | 1.37 G |
| Storage temperature (T-T) | -40 - 65 °C |
| Operating temperature (T-T) | 10 - 35 °C |
| Storage relative humidity (H-H) | 5 - 95 % |
| Operating relative humidity (H-H) | 20 - 80 % |
Weight and Dimensions| Depth | 178.56 mm |
|---|---|
| Width | 36 mm |
| Height | 182 mm |
| Weight | 1380 g |
| Package depth | 238 mm |
| Package width | 498 mm |
| Package height | 133 mm |
| Package weight | 2910 g |
To Next Page
