Dell S2421Ht - Removing the Monitor Stand

Setting up the monitor | 29
Wall mounting (Optional)
DELL S2421H
Flat Panel Monitor / 液晶显示器
型号 : S2421H
Input Rating / 输入电源 :
100-240V ~ 50/60Hz 1.5A
Made in China / 制造地:中国
Manufactured date / 制造日期:
E
t
DELL S2421H
Flat Panel Mon itor / Moni tor Plano P anel / Moni teur à écr an plat / 液 晶顯示器
Model No. / N° de Modelo / Numéro de m odèle /型號: S2421Ht
Input Rating / Entrada / Daya Tegangan / Tension d’ent rée: 100-240V ~ 50/60Hz 1.5A
輸入電源: 交流電壓 100-240伏特, 1.5安培, 50/60赫茲
Удельная мощность рабочего режима -X,XXX Вт/см
2
Потребляемая мощность изделием в режиме ожидания -X,XX Вт
Потребляемая мощность изделием в выключенном режиме - X,XX Вт
Made in China / Fabricado en China / Fabriqué en Chine / Сделано в Китае / 製造地:中國
警語: 使用過度恐傷害視力
신청인: Wistron Corporation (For Korea)
Wistron InfoComm (Zhongshan) Corporation Linhai Branch
제조자: Wistron InfoComm (Zhongshan) Corporation Linhai Branch
A/S 연락처: 080-854-0066
제조국: 중국
CAN ICES-3 (B)/NMB-3(B)
Apparatet må tilkoples jordet stikkontakt.
Apparaten skall anslutas till jordat uttag.
Apparatets stikprop skal tilsluttes en stikkontakt med jord,
som giver forbindelse til stikproppens jord.
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan.
Consumo de energía en operación: XX.XX Wh
XXXXX
Address for EU Only:
Raheen Business Park
Limerick Ireland
www.dell.com/regulatory_compliance
XXXXXXXX-XXXXX
R-R-WT1-S2421Ht
И005-20
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
XXXXXX-XX
IS 13252 (Part 1)/
IEC 60950-1
R-41071650
www.bis.gov.in
For UK only: Cain Road, Bracknell, RG12 1LF
ID XXXXXXXXXX
ID XXXXXXXXXX
NOTE: Use M4 x 10 mm screws to secure the wall-mounting kit to the
monitor.
See the documentation that is shipped with the VESA-compatible wall mounting kit.
1. Place a at cushion or a sitting mat near the edge of a table and place the
monitor on it with the display facing down.
2. Remove the stand.
3. Using a Phillips crosshead screwdriver, remove the four screws that secure the
back panel.
4. Connect the mounting bracket from the wall mounting kit to the monitor.
5. Follow the instructions that shipped with the wall-mounting kit and mount the
monitor on the wall.
NOTE: For use only with UL or CSA or GS-listed wall mount bracket
with minimum weight/load bearing capacity of 13.8 kg (S2421H)/17.6 kg
(S2721H).