Dell SonicWALL TZ300 User Manual

Dell SonicWALL TZ300 Quick Start Guide
TZ300 front and back panels
Figure 1. Front and back panels
Rear Panel
SonicWALL TZ300
X0 X1 X2 X3 X4
1000/act
10/100/act
lan wan
U0
ss
1000
wan
X0X1X2X3X4
lan
power
console
Front Panel
USB 3.0 port
Power
Test
Fast blinking is initializing
Slow blinking is SafeMode
Service
For future use
Top - 10/100 Mbps when lit
Bottom - 1 Gbps when lit
X1 WAN Port
X4/X3/X2
Power
Console
Port
X0 LAN Port
Congurable ports
1 Check package contents
Verify that your package has the following contents:
• Dell SonicWALL appliance
• Ethernet cable
• Standard power adaptor
• Standard power cord
• Quick Start Guide
Figure 2. Package Contents
NOTE: The included power cord is approved for use
only in specific countries or regions. Before using a
power cord, verify that it is rated and approved for
use in your location.
SonicWALL TZ300
X0 X1 X2 X3 X4
1000/act
10/100/act
lan wan
U0
ss
1000
2 Power on
• Connect the power adaptor to the appliance and to
the power cable. Plug the power cable into an
appropriate outlet (110-240 volts).
• The TZ appliance powers on and the Test LED
blinks during the boot sequence.
120V AC
(U.S.)
Internet
U0
ss
SonicWALL TZ300
X0 X1 X2 X3 X4
1000/act
10/100/act
lan wan
1000
U0
ss
SonicWALL TZ300
X0 X1 X2 X3 X4
1000/act
10/100/act
lan wan
1000
3
Connect the interfaces
• Connect the WAN interface (X1) to your Internet
connection using a standard Ethernet cable.
• Connect the LAN interface (X0) to your computer
using a standard Ethernet cable.
Figure 3. Connecting WAN and LAN interfaces
wan
X1
lan
X0
Internet
4 Run the Setup Wizard
• In the Web browser on your computer, navigate to
https://192.168.168.168.
• In the window that opens, click on the word here
in the line that says, “To launch the Dell
SonicWALL Setup Wizard, click here.”
http://192.168.168.168/
http://192.168.168.168/
TIP: Your computer should be using DHCP IP
addressing.
• The SonicOS Startup Guide opens.
• Click Next and follow the prompts in the Startup
Guide pages that follow.
• Enter the TZ appliance administrator credentials
to change the password, if you wish. Click Next.
NOTE: The default administrator credentials are
Username: admin Password: password
• The automatic WAN IP settings are displayed.
Click Next.
• The new IP Configuration is displayed. Click Done.
NOTE: For manual configuration, refer to the
SonicOS 6.2 Administration Guide.
Dell SonicWALL™ TZ300
Quick Start Guide
Regulatory Model Number: APL28-0B4

Dell SonicWALL TZ300 Specifications

General

Brand	Dell
Model	SonicWALL TZ300
Category	Firewall
Language	English

Summary

Dell SonicWALL TZ300 Hardware Overview

TZ300 Front and Back Panels

Diagrams and descriptions of the front and rear panel interfaces and indicators of the Dell SonicWALL TZ300 appliance.

Initial Setup and Configuration

Check Package Contents

Verify all required components, including the Dell SonicWALL appliance, cables, and power adapter, are present in the package.

Power On the Appliance

Connect the power adaptor and cable, then plug into an outlet to power on the TZ appliance and observe the Test LED.

Connect Network Interfaces

Connect the WAN interface (X1) to the internet and the LAN interface (X0) to your computer using Ethernet cables.

Run the Setup Wizard

Access the appliance via a web browser, navigate to the setup wizard, and follow prompts to configure initial settings.

Product Registration and Firmware Update

Register Your Product

Log in to MySonicWALL, register the appliance by entering serial and authentication codes for access to services and firmware.

Get the Latest Firmware

Download the latest firmware from MySonicWALL, upload it to the appliance via the web interface, and select it for boot.

Safety and Regulatory Information

Mounting and Installation Precautions

Guidelines for safe mounting, including location, ventilation, cable routing, and using appropriate hardware for installation.

Lithium Battery Warning

Information regarding the lithium battery, stating it is not user-replaceable and requires authorized service for replacement.

Cable Connection Safety

Instructions to use Ethernet and RS232 cables for intra-building connections only, avoiding direct connection to external wiring.

Power Supply Requirements

Details on using a UL-listed power supply marked 'I.T.E. LPS' with specific voltage and amperage ratings for safe operation.