How to fix a DeLonghi HCX Heater that doesn't work?
If your DeLonghi Heater isn't working, first, ensure it's properly plugged into a working electrical outlet. If it is, the temperature setting might be too low; try increasing it. Also, check if the Key lock is activated (refer to the "Key lock" section for deactivation). Finally, verify that the timer is correctly programmed.
What to do if DeLonghi HCX Heater doesn't work and beeps?
If your DeLonghi Heater isn't working, and the display is blinking with an intermittent beep, the air intake or outlet grille might be blocked. Remove any obstructions, unplug the heater from the mains, and allow it to cool down. After a few minutes, plug it back in. If it still doesn't work, contact De'Longhi Customer Experience.
What to do if my DeLonghi HCX Heater doesn't work and beeps?
If your DeLonghi Heater isn't working, the display is blinking, and you hear an intermittent beep, the air intake or outlet grille might be obstructed. Remove the obstruction, remove the plug from the mains and let the appliance cool down. After a few minutes, plug the appliance in again. If it still doesn't work, please contact Customer Experience.
Why is my DeLonghi HCX Heater beeping and showing a blinking dot?
If the display of your DeLonghi Heater shows a blinking dot and you hear an intermittent beep, it could be tipped over or positioned improperly. Make sure the appliance is standing upright on a flat surface and is positioned correctly.
Why does my DeLonghi HCX Heater display "Ht" blinking?
If the display on your DeLonghi Heater shows "Ht" blinking and the heating power is reducing, it means the internal temperature is too high. Ensure that nothing is covering or obstructing the unit. Also, make sure the heater is positioned correctly, respecting the minimum distances from the wall or other objects. The appliance should resume normal operation after a few minutes.
Why does my DeLonghi Heater display 'Ht' blinking?
The 'Ht' blinking on your DeLonghi Heater indicates that the internal temperature is too high. Ensure that the unit is not covered or obstructed. Also, check that the appliance is correctly positioned, respecting the minimum distances from the wall or other objects. If it is not, position the appliance correctly. The appliance will operate again after a few minutes.
What to do if my DeLonghi HCX display shows a blinking dot and I hear an intermittent beep?
If your DeLonghi Heater's display shows a blinking dot and you hear an intermittent beep, it means the appliance may have been tipped over or is not positioned correctly. Make sure the appliance is standing upright on a flat surface and position it correctly.
Why does my DeLonghi HCX show a blinking dot and beep?
If the display of your DeLonghi Heater shows a blinking dot and you hear an intermittent beep, it might have been tipped over or is improperly positioned. Ensure the appliance is upright on a flat surface and correctly positioned.
Why is my DeLonghi HCX not working and beeping?
If your DeLonghi Heater isn't working, the display is blinking, and you hear an intermittent beep, it indicates that the air intake or outlet grille is obstructed. Remove the obstruction, unplug the heater from the mains, and let the appliance cool down. After a few minutes, plug the appliance in again.
What does "PF" mean on my DeLonghi HCX Heater display?
If the display of your DeLonghi Heater shows "PF", the temperature sensor is malfunctioning. Contact the nearest customer service.
General| Mounting | Freestanding |
|---|---|
| Pre-assembled feet | Yes |
| Oscillation | No |
| Thermostat | Adjustable |
| Safety Features | tip-over switch |
| Handle | Yes |
General safety instructions and precautions for using the appliance safely.
Use this heater only as described in this manual. All other use is considered improper.
The appliance must not be disposed of with household waste, but taken to an authorised recycling centre.
Important warnings are identified by symbols. It is important to respect the warnings.
The plug may get warm during use; ensure wall sockets are in good condition and plug is inserted correctly.
Remove heater from packaging, check for damage, and remove publicity material before operation.
Check voltage and power consumption compatibility before connecting to the outlet.
Turn appliance upside down on a soft surface to fix feet with supplied screws.
Instructions for wall mounting using the provided kit, including drilling and fixing brackets.
Plug in, appliance beeps and power light illuminates. Appliance starts heating according to current settings.
Maintains room temperature at 7°C to prevent freezing.
Selectable heating powers (low, medium, high) with optional fan, adjustable via +/- buttons.
Automatically adjusts power level for optimum comfort and energy saving in heating modes.
Indicator lights (red, yellow, green) show heating status: max, medium, or minimum power.
The display offers two brightness settings, with the highest active when a key is pressed.
Press '+' and '-' together for 3 seconds to lock/unlock the keyboard and prevent accidental operation.
Allows setting a delayed start or delayed stop for the appliance using the timer button.
Press and hold '+' for 10 seconds in standby to switch between °F and °C temperature scales.
Unplug and cool down before cleaning. Use a soft, dry cloth. Avoid abrasive powders or solvents.
Details on power supply and absorbed power, refer to the rating label.
Check plug, socket, temperature setting, key lock, and timer programming.
Ensure air intake/outlet grilles are clear. If display blinks with beeps, check for tipping or obstructions.
Display showing 'PF' indicates sensor malfunction. Display showing 'Ht' indicates internal overheating.
Details on fuse rating (13 Amp) and UK plug wiring (blue to N, brown to L).
To Next Page