Delta DVP04DA-S2 User Manual

Warning
EN  DVP04DA-S/DVP04DA-S2 is an OPEN-TYPE device. It should be installed in a control cabinet free of airborne dust, humidity, electric shock
and vibration. To prevent non-maintenance staff from operating DVP04DA-S/DVP04DA-S2, or to prevent an accident from damaging
DVP04DA-S/DVP04DA-S2, the control cabinet in which DVP04DA-S/DVP04DA-S2 is installed should be equipped with a safeguard. For
example, the control cabinet in which DVP04DA-S/DVP04DA-S2 is installed can be unlocked with a special tool or key.
EN
 DO NOT connect AC power to any of I/O terminals, otherwise serious damage may occur. Please check all wiring again before
DVP04DA-S/DVP04DA-S2 is powered up. After DVP04DA-S/DVP04DA-S2 is disconnected, Do NOT touch any terminals in a minute. Make
sure that the ground terminal
on DVP04DA-S/DVP04DA-S2 is correctly grounded in order to prevent electromagnetic interference.
FR  DVP04DA-S/DVP04DA-S2 est un module OUVERT. Il doit être installé que dans une enceinte protectrice (boitier, armoire, etc.) saine,
dépourvue de poussière, d’humidité, de vibrations et hors d’atteinte des chocs électriques. La protection doit éviter que les personnes non
habilitées à la maintenance puissent accéder à l’appareil (par exemple, une clé ou un outil doivent être nécessaire pour ouvrir a protection).
FR
 Ne pas appliquer la tension secteur sur les bornes d’entrées/Sorties, ou l’appareil DVP04DA-S/DVP04DA-S2 pourra être endommagé. Merci
de vérifier encore une fois le câblage avant la mise sous tension du DVP04DA-S/DVP04DA-S2. Lors de la déconnection de l’appareil, ne pas
toucher les connecteurs dans la minute suivante. Vérifier que la terre est bien reliée au connecteur de terre
afin d’éviter toute
interférence électromagnétique.
 Introduction
 Model Explanation & Peripherals
 Thank you for choosing the Delta DVP series PLC. A DVP series slim type PLC can read data from DVP04DA-S/DVP04DA-S2 or write
data to DVP04DA-S/DVP04DA-S2 by means of the instruction FROM/TO. The analog output module receives four pieces of 12-bit
digital data from a PLC, and converts the digital data into 4-point analog signal output (voltage or current). There are 49 CRs (control
registers) in the module, and each register has 16 bits.
 Users can select output from voltage or current via wiring. Voltage output range is 0V ~ +10VDC (resolution is 2.5mV). Current output
range is 0mA ~ 20mA (resolution is 5μA).
 Product Profile & Outline
90.00
4.00
3.00
25.20
1
2
3
4
60.0
0
5
6
7
8
9
3
10
●
FG
V+
I+
COM
C
H
1
FG
V+
I+
COM
C
H
2
FG
V+
I+
COM
C
H
3
FG
V+
I+
COM
C
H
4
11
12
13
3.4
90.00
60.0
0
3.00
14
●
Unit: mm Figure 1
1. POWER, RUN and ERROR indicators 8. Extension port
2. Model name 9. Extension unit clip
3. DIN rail clip 10. DIN rail groove (35mm)
4. I/O terminals 11. RS-485 communication port
5. I/O point indicators 12. Mounting groove of the extension unit
6. Mounting hole of the extension unit 13. DC power input
7. Nameplate 14. Extension port
 External Wiring
ENGLISH

Delta DVP04DA-S2 Specifications

General

Brand	Delta
Model	DVP04DA-S2
Category	I/O Systems
Language	English