EasyManuals Logo

Denon AVR-X3800H User Manual

Denon AVR-X3800H
321 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #295 background imageLoading...
Page #295 background image
z1
During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
z2
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played.
z3
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS:X, DTS-HD or DTS signal is played.
z4
This item can be selected when a DTS:X signal that is compatible with the Dialog Control function is input.
z5
This can be set when the LFE signal is included in the input signal.
z6
This item can be selected when Height, Ceiling or Dolby Atmos Enabled speakers are used.
z7
This item can be set when any Height, Ceiling or Dolby Atmos Enabled speakers are not used, or Surround speakers are not used.
z8 This item can be selected when “Surround Parameter” - “IMAX Audio Settings” in the menu is set to “Manual”. (v p. 166)
z9 This item cannot be set when “Dynamic EQ” is set to “On”. (v p. 174)
z10 This item cannot be set when “Speaker Configuration” - “Subwoofer” in the menu is set to “None”. (v p. 214)
z11
This item cannot be set when Audyssey
®
Setup (Speaker Calibration) has not been performed.
z12
This item cannot be selected when a DTS:X format with a sampling frequency of over 48 kHz is input.
z13
This item cannot be set when sound mode is “DTS Virtual:X” or sound mode that have “+Virtual:X” in the sound mode name.
z14
This item cannot be set when “MultEQ
®
XT32” in the menu is set to “Off”. (v p. 173)
z15
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
z16 This setting is available when “Bass” - “Subwoofer Output” in the menu is set to “LFE + Main”. (v p. 225)
z17 This item can be set when “Speaker Configuration” - “Front” is set to “Small” or “Bass” - “Subwoofer Output” is set to “LFE + Main”. (v p. 214, 225)
z18
This cannot be set if the input signal contains Auro-3D signals containing a Height channel.
z19
This can be set if the input signal contains an Auro-3D signal.
Contents
Connections Playback Settings Tips Appendix
295
Front panel Display Rear panel Remote Index

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X3800H and is the answer not in the manual?

Denon AVR-X3800H Specifications

General IconGeneral
Channels9.4
HDMI Outputs3
Dolby AtmosYes
DTS:XYes
Wi-FiYes
BluetoothYes
HEOS Multi-roomYes
Voice ControlYes (Amazon Alexa, Google Assistant, Apple Siri)
eARCYes
Input Sensitivity/Impedance200 mV / 47 kohms
EthernetYes
Phono InputYes
AM/FM TunerYes
Audyssey Room CorrectionAudyssey MultEQ XT32
HDR CompatibilityHDR10+, Dolby Vision, HLG
StreamingSpotify, Tidal
Frequency Response10 Hz - 100 kHz (+1, -3 dB)
USB PortYes
Signal-to-Noise Ratio100 dB (IHF-A weighted, Direct mode)

Related product manuals