EasyManuals Logo

Denon AVR-X4800H User Manual

Denon AVR-X4800H
339 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #215 background imageLoading...
Page #215 background image
o
About the main listening position
The main listening position is the position where listeners would
normally sit or where one would normally sit alone within the listening
environment. Before starting Audyssey
®
Setup, place the Sound
calibration microphone in the main listening position.
Audyssey MultEQ
®
XT32 uses the measurements from this position to
calculate speaker distance, level, polarity, and the optimum crossover
value for the subwoofer.
o
About Audyssey Sub EQ HT™
Audyssey Sub EQ HT™ makes the integration of dual subwoofers
seamless by first compensating for any level and delay differences
between the two subwoofers and then applying Audyssey MultEQ
®
XT32 to both subwoofers together.
To run Audyssey Sub EQ HT™ you must select “Measure (2 spkrs)” in
“Channel Select”. (v p. 217).
NOTE
0
Make the room as quiet as possible. Background noise can disrupt the room
measurements. Close windows and turn off the power on electronic devices
(radios, air conditioners, fluorescent lights, etc.). The measurements could be
affected by the sounds emitted by such devices.
0
During the measurement process, place cell phones outside the listening room.
Cell phone signals could disrupt the measurements.
0
Do not stand between the speakers and Sound calibration microphone or allow
obstacles in the path while the measurements are being made. Also, install the
Sound calibration microphone at least 50 cm away from the wall. Failure to do so
will result in inaccurate readings.
0
During the measurement process, audible test tones will come from the speakers
and subwoofer(s), but this is part of normal operation. If there is background noise
in the room, these test signals will increase in volume.
0
Operating VOLUME d f on the remote control unit or MASTER VOLUME on the
main unit during the measurements will cancel the measurements.
0
Measurement cannot be performed when headphones are connected. Unplug the
headphones before performing Audyssey
®
Setup.
Contents
Connections Playback Settings Tips Appendix
215
Front panel Display Rear panel Remote Index

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X4800H and is the answer not in the manual?

Denon AVR-X4800H Specifications

General IconGeneral
Channels9.4
Dolby AtmosYes
DTS:XYes
HDMI Inputs7
HDMI Outputs3
4K/120Hz Pass-throughYes
8K SupportYes
Wi-FiYes (2.4GHz/5GHz)
BluetoothYes
HEOS Built-inYes
Amplifier Channels9
Power Output per Channel @ 8 Ohms / 1 kHz / 0.08% THD / 2 Channels Driven125W
Speaker Impedance4-16 Ohms
Auro 3DYes
IMAX EnhancedYes
HDCP Support2.3
HDR CompatibilityHDR10, HDR10+, Dolby Vision, HLG
eARC SupportYes
Phono InputYes
EthernetYes
Voice Assistant SupportAmazon Alexa, Google Assistant, Apple Siri
Audyssey MultEQ XT32Yes
Total Harmonic Distortion0.05%
Input Sensitivity/Impedance200 mV / 47 kOhms
Network ConnectivityEthernet, Wi-Fi
Supported Audio FormatsMP3, WMA, AAC, FLAC, ALAC, WAV, DSD
Dimensions (W x H x D)434 x 167 x 389 mm
Weight13.5 kg
Power Output per Channel125W
Voice ControlYes
Frequency Response10 Hz - 100 kHz
DAC32-bit AKM
Video Pass-Through8K
Zone Audio OutputZone 2, Zone 3
Wireless Audio StreamingYes
Signal-to-Noise Ratio102 dB
Video Inputs/Outputs7/3 (HDMI)
Audio Inputs/Outputs7 HDMI inputs, 3 HDMI outputs, 1 phono input, 2 optical inputs, 1 coaxial input

Related product manuals