Denon DCD-1520 - Remote Control Unit Functions; Direct and Program Search; Volume and Mode Controls; Troubleshooting Guide

REMOTE CONTROL UNIT RC-216
Number buttons (1 through 0)
Play button ( » PLAY)
Automatic search reverse button ( Iq }
Automatic search forward button ( PPI)
Pause button ( Il PAUSE)
Stop button ( HI STOP)
Setting to the Program Mode
e For program search, press the PROGRAM
button then the number buttons (0 through
9 and +10).
The remote controi unit is normally set to
the direct mode.
+10 button
Program button (PROGRAM)
Direct button (DIRECT)
Call button (CALL)
Manual search reverse button ( 44 )
Manual! search forward button ( PP )
Display (DISPLAY)
Clear Button (CLEAR)
Index button (INDEX)
1-track repeat button (1)
All tracks repeat button (ALL)
Auto edit button (AUTO EDIT)
Auto space button (AUTO SPACE)
Time Search Button (TIME SEARCH)
Time mode button (TIME) | [| __ Volume buttons (VOLUME)
These control the output level of the VARIABLE
output terminal.
The volume increases when the (+) button is
pressed, decreases when the {—) button is pressed.
e Direct Search
Normally, direct search is possible simply by pressing the desired
number buttons.
e Program Search (During playback, the track which is currently playing
is programmed as the 1st track.)
Press the PROGRAM button, then press the number buttons.
For example, to program tracks number 3, 11, and 5, press
PROGRAM — 3 — +10 and 1 — 5.
To cancel the program, press the DIRECT button.
TROUBLESHOOTING
lf the CD player does not seem to be functioning properly, check the
following:
Disc holder does not open or close.
e ls the power on?
When a disc is loaded, 00000000 is displayed.
e Isthe disc loaded properly? ... See page 6
When the play button ( » PLAY) is pressed, playback does not start.
@ = Isthe disc dirty or scratched? .........ceccsseeseseesenetenens See page 10
There is no sound, or it is distorted.
e ls the output cord properly connected to
We BMIPHTOL? cK ccsntspgetenantriortieriier cidade csnnteanater See page 6
e Have the amplifier controls been set correctly?
Inputting the Track Numbers
For track numbers below 9, simply press the corresponding button. For
track numbers of 10 and greater, press the +10 then the number
buttons.
For example, for track number 22 press +10 twice then 2.
Volume
The volume control on the unit will operate when the volume buttons
are pressed. The volume can be checked by looking at the position of
the control.
A specific section of the disc will not play.
e Isthe disc dirty or scratched? ...
Programmed playback does not work.
e Have programming been properly done? ..... See pages 7 and 11
Incorrect operation when buttons on the remote control are pressed.
e ts the remote control unit being operated
too far from the CD player? oo... cceesceeseserrerreereeee See page 10
e Are there obstacles blocking the ray?
e Is the remote control sensor exposed to strong light?
e Are the batteries exhausted?
See page 10
SPECIFICATIONS
AUDIO
No. of Channels: 2 channels
Frequency Response: 2 ~ 20,000 Hz
Dynamic Range: 100 dB
Signal-to-noise Ratio: 115 dB
Harmonic Distortion: 0.0025% (1 kHz)
Separation: 103 dB (1 kHz)
Wow & Flutter: Below measurable limit:
(+0.001% W.peak)
Output Voltage: 2.0 V, VARIABLE 0~2.0 V
DISCS Compact Disc format
GENERAL CHARACTERISTICS
Power Supply: 50/60 Hz, voltage is shown on rating label
Power Consumption: 22 W
Dimensions: 434 (17.1 in) W x 135 (5.3 in) H x
. 350 (13.8 in) D mm
Weight: 10.7 kg
FUNCTIONS AND DISPLAY
Functions: Direct selection, automatic search,
programmed playback, repeat playback,
manual search, auto space, time mode,
auto edit, emphasis feature
Display: Track number, time, music calendar,
and engaged modes
Others: Headphones jack
REMOTE CONTROL UNIT RC-216
Remote Control System: Infrared pulse system
Power Supply: 3 V DC; two SUM-4 (standard size AAA)
dry cell batteries
External Dimensions: 60 (2.4 in) W x 165 (6.5 in) H x 17(0.7 in} Dmm
Weight: 95 g (including batteries)
SUPPLIED ACCESSORIES Pin-plug connection cord, mini screwdriver,
* Design and specifications are subject to change without notice in the course of product improvement.
11