Denon DN-D9000 - Splice Function Details; Setting Splice Points; Splice Playback and Clearing

15
ENGLISH
RVS
PLAY/PAUSESTUTTER AUTO
REMOTE CONTROLLER RC-D90
0%
TRACK PARAMETERS
PITCH BEND PITCH/KEY
PITCH/VOL SPLICE
A/B TRIM
4 HOT START
SAMPLER
STOP
B
SAMP2 EXIT/RELOOP SAMP1
A3 A4 CUE
A1 A2
CLR
CLR
F
X
PLAY/PAUSESTUTTER
SAMPLER
B SAMP2SAMP1
A3 A4 CUE
A1 A2
CLR
CLR
RVS
A 3/4
PUSH
ON/OFF
MEMO
PRESET
RANDOM
PROGRAM
TIME
TOTAL TIME RELAY
CONT./SINGLE
ALL OFF
PLATTER MODE MEMO
PRESET
RANDOM
PROGRAM
TIME
TOTAL TIME RELAY
CONT./SINGLE
sm
CONT.
f
SINGLE
B
B
A4
A2
REMAIN
s
m
TOTAL
BA3
BA1
ELAPSED
sm
CONT.
f
SINGLEREMAIN
s
m
TOTAL
BA3
BA1
ELAPSED
DRAG S.
DUMP
BRAKE
RVS
ECHO
KEY ADJ.
PROG
MEMO
KEY A
D
PROG
MEMO
CUE
FLIP
FLIP
A 3
A 1
A 4
A 2
B
B
EXIT/
RELOOP
RELOOP
EXIT/
CUE
OPEN/
CLOSE
TAP
CUE
FLIP
FLIP
A 3
A 1
A 4
A 2
B
B
-TRACK PLAY-TRACK HOT START
S
E
A
H
C
L
F
M
X
G
F
L
D
E
F
I
R
L
B
E
D
N
H
C
S
E
A
/
D
B
E
R
N
R
D
I
S
O
E
C
R
U
L
L
F
F
O
RANGE
B
Y
S
S
A
A
P
S
E
T
C
E
H
C
T
R
C
S
L
A
-TRACK HOT START
w, r, t
t
e
q
1
Splice point setting mode
q Push the SPLICE button for
more than 1 sec to enable
setting Splice point using A1,
A2 and B buttons.
• The A button illumination flashes when
the Splice mode is set.
• The Splice point setting cannot be set
for the A point at which Hot Start data
is already loaded.
SPLICE
A/B TRIM
Splice
2
Set splice start point A
w After starting playback, push
the A1 or A2 button. The
corresponding A button lights
up and that point is set as
splice start point A, and B LED
start flashing.
A 1
3
Set splice end point B
e After setting splice start point
A, push the B button. The B
LED lights up and that point is
set as splice end point B.
B
5
Temporarily turning off the splice playback
r When the corresponding A
button is pushed after setting
splice points A and B, the A
button illumination turns off
and the Splice play mode is
temporarily turned off.
• Push the corresponding A button again
to resume splice playback.
A 1
• Use this function to skip a section between A and B points. The A point is the point from which jumping starts,
the B point the point at which jumping ends.
• The A1 and A2 Hot Starts and Stutter functions cannot be used if both Splice points are set in the Splice mode.
4
Start splice playback
Start playback from any point before point A.
When point A is reached, the section from
point A to point B is jumped seamlessly and
playback continues.
6
Clearing the splice points
t While pressing the FLIP/(CLR) button, push
the corresponding A button to clear splice
points A and B.
• When the splice points are cleared, the
A button is set back to the hot start
mode.
A 1
FLIP