Denon DN-D9000 - Seamless Loop, Hot Start, Stutter, and Splice; Setting Loop and Hot Start Points; Stutter Playback and Clearing Points

14
ENGLISH
9
SEAMLESS LOOP/HOT START/STUTTER AND SPLICE
RVS
PLAY/PAUSESTUTTER AUTO
REMOTE CONTROLLER RC-D90
0%
TRACK PARAMETERS
PITCH BEND PITCH/KEY
PITCH/VOL SPLICE
A/B TRIM
4 HOT START
SAMPLER
STOP
B
SAMP2 EXIT/RELOOP SAMP1
A3 A4 CUE
A1 A2
CLR
CLR
F
X
STUTTER
SASAMP1
A3 A4 CUE
A1 A2
CLR
CLR
RVS
A 3/4
PUSH
ON/OFF
MEMO
PRESET
RANDOM
PROGRAM
TIME
TOTAL TIME RELAY
CONT./SINGLE
ALL OFF
PLATTER MODE M
PR
TIME
TOTAL TIME RELAY
CONT./SINGLE
sm
CONT.
f
SINGLE
B
B
A4
A2
REMAIN
s
m
TOTAL
BA3
BA1
ELAPSED
m
REMAIN
s
m
TOTAL
BA3
BA1
ELAPSE
DRAG S.
DUMP
BRAKE
RVS
ECHO
KEY ADJ.
PROG
MEMO
PROG
MEMO
CUE
FLIP
FLIP
A 3
A 1
A 4
A 2
B
B
EXIT/
RELOOP
RELOOP
EXIT/
CUE
OPEN/
CLOSE
TAP
CUE
FLIP
FLIP
A 3
A 1
A
A
-TRACK PLAY-TRACK HOT START
S
E
A
H
C
L
F
M
X
G
F
L
D
E
F
I
R
L
B
E
D
N
H
C
S
E
A
/
D
B
E
R
N
R
D
I
S
O
E
C
R
U
L
L
F
F
O
RANGE
B
Y
S
S
A
A
P
S
E
T
C
E
H
C
T
R
C
S
L
A
-TRACK HOT START
q, w, y
Operation display
(refer to the section
describing the display)
t, y
e
r
1
4
Setting the A point (loading the Hot Start
data)
q Push the A1 or A2 button to
set the A point and Hot Start
data loading starts.
• A1 and A2 buttons can be used
separately for each Hot Start.
• When an A point is set, the
corresponding A button and FLIP LED
light and that button is set to the Hot
Start mode.
• The BPM is set independently for each
hot start.
Playing seamless loops
• When the B point for A1 is detected after
playback started from A1 point, playback
returns to A1 point with seamless. While
A1 to B looping, B point for A2 ignored.
• When the B point for A2 is detected after
playback started from A2 point, playback
returns to A2 point with seamless. While
A2 to B looping, B point for A1 ignored.
3-2
• If the B button is pushed during
seamless loop playback or after EXIT
playback, the B point moves to the
point at which the button was pushed.
• When the B point is set, the B and
LOOP LEDs light.
A 1
Seamless Loop/Hot Start/Stutter (A1, A2 buttons)
2
Starts Hot Start
w When A1 or A2 button is
pushed, Hot Start playback
starts from the corresponding
A point.
A 1
3-1
Setting the B point for Seamless Loop
e When the B button is pushed
after setting the A point or
after starting Hot start
playback, the B point is set
and Seamless Loop playback
starts from the A point.
• The B button works with respect to the
A point operated before the B button
was pushed.
B
5
Exit/Reloop
r In Seamless Loop playback,
you can force exit from or
return in the loop.
EXIT:
While the Seamless Loop playback, push
the EXIT/RELOOP button to exit from
loop. DN-D9000 continues playback after
the B point.
RELOOP:
When the EXIT/RELOOP button is pushed
after exit the loop, Seamless Loop
playback resumes from the A point.
EXIT/
RELOOP
6
Stutter
• A1 and A2 points can be also used for
Stutter playback.
t To enable stutter playback,
push FLIP button for A1/A2
buttons, then FLIP LED turns
off.
Press the FLIP button to switch between
the Hot Start/Seamless Loop and Stutter
modes.
7
Clear the A1/A2 point
y While pressing the FLIP/(CLR) button, push
the A1 or A2 button to clear the
corresponding A and B points.
Or push the Flip button for more than 1 sec
to clear both A1 and A2 points at once.
FLIP
A 1
FLIP