To Next PageTo Next PageWhat to do if Denon S-5BD reception fails?
If reception fails or there is a lot of noise or distortion, try changing the antenna orientation or position. Separate the AM loop antenna from the unit, and consider using an FM outdoor antenna. Also, keep the antenna separate from other connection cables.
Why is the power indicator blinking red on my Denon S-5BD every 2 seconds?
If the power indicator is blinking red in intervals of approximately 2 seconds, the temperature inside the unit has likely risen. Turn off the power and re-apply it after the temperature has sufficiently cooled down. Also, reinstall the unit in a place with good ventilation.
What causes Denon S-5BD picture to freeze during playback?
If the picture freezes momentarily during playback, the disc may be scratched or dirty; try cleaning or replacing it. Alternatively, there may be a problem with the recorded disc.
Why is the power indicator blinking red on my Denon Receiver?
If the power indicator is blinking red in intervals of approximately 0.5 seconds, it could be due to the speaker cable being shorted (touching). Firmly twist the core wire in the speaker cable and reconnect it to the speaker terminal. Also, make sure that you use speakers with the specified impedance.
What to do if Denon Receiver has no video with HDMI connection?
If there is no video output with the HDMI connection, check the connection of the HDMI connectors. Ensure the input source matches the connected HDMI connector. Also, verify that the TV is compatible with copyright protection (HDCP); otherwise, video will not output correctly. Lastly, confirm that the HDMI video resolution set in this unit is compatible with the TV resolution, or set it to “Auto” for automatic configuration.
Why does Denon S-5BD Receiver audio input to the OPTICAL connector not output?
If audio input to the OPTICAL connector is not output, set “Source Select” – “Input Mode” on the GUI menu to “Auto” or “Digital”. Also, make sure that “Manual Setup” – “Audio Setup” – “COAX Input Assign” on the GUI menu is set to “OFF”.
Why does Denon S-5BD Receiver audio input to the COAXIAL connector not output?
If audio input to the COAXIAL connector is not output, set “Manual Setup” – “Audio Setup” – “COAX Input Assign” on the GUI menu to “AUX1” or “AUX2”.
How to fix Denon Receiver Dolby TrueHD audio not output?
If Dolby TrueHD, DTS-HD, or Dolby Digital Plus audio is not being output, make HDMI connections.
How to fix Denon S-5BD DTS sound not output?
If DTS sound is not being output, set “Decode Mode” on the GUI menu to “Auto” or “DTS”.
How to fix Denon Receiver no sound from front height speaker?
If no sound is produced from the front height speaker, set “Audio Adjust” – “Surround Parameters” – “Front Height” on the GUI menu to “ON”. Additionally, set “Manual Setup” – “Speaker Setup” – “Speaker Assign” on the GUI menu to “5.1CH + Front Height”.
General| Receiver type | Surround |
|---|---|
| Audio output channels | 5.1 channels |
| Power output per channel (20-20KHz@8 Ohm) | 75 W |
| HDMI in | 3 |
| Audio (L/R) in | 2 |
| S-Video inputs quantity | 1 |
| Speakers connectivity type | - |
| Audio formats supported | AAC, MP3, WAV, WMA |
| Image formats supported | JPG |
| Video formats supported | AVCHD, DIVX |
| Ethernet LAN | Yes |
| Supported radio bands | AM, FM |
| Optical drive type | Blu-Ray player |
| Disc types supported | BD-R, CD-R, CD-RW, DVD+R, DVD+RW, DVD-R, DVD-RW |
| Compatible memory cards | SD |
| Supported video modes | 1080p |
| AirPlay | No |
| Display | LCD |
| Product color | Black |
| Audio decoders | Dolby Digital, Dolby Pro Logic II, Dolby Pro Logic IIz, DTS |
| Apple docking compatibility | iPhone, iPod |
| Cables included | AC |
| Remote control type | RC-1072 |
Weight and Dimensions| Depth | 365 mm |
|---|---|
| Width | 434 mm |
| Height | 117 mm |
