Denon UDRA-70 - PART NAMES AND FUNCTIONS; RECEIVER DISPLAY

ENGLISH
PART NAMES AND Cone
DENON seru steno acenen
we
|
[nF
O,
G0
me
a
mmo)
mie
o
yaaa
steno
NO
This diagram shows the trap door open.
—]
POWER switch
Press this switch once to turn on the power and the display.
The displays on the CD player and cassette deck also light.
The CD player’s play indicator does not light.
The cassette deck’s direction of play indicator lights.
SDB (Super Dynamic Bass) indicator
This lights when the SDB function is turned on with the SDB button.
REMOTE SENSOR
VOLUME control
Use this control to adjust the volume.
Turn clockwise ( ) to increase the volume, counterclockwise
(© ) to decrease it.
PHONES jack
When using headphones, plug them in here.
The sound from the speakers is cut when headphones are plugged
These are used to preset and recall AM and FM broadcasts, to set
the time and timer, etc.
MEMORY button
This button is used when presetting AM and FM stations.
idpeab ieee (FM stereo mute/mono) selector
utton
(For FM reception)
STEREO mute: Use this mode to receive FM broadcasts in stereo.
(“AUTO” appears on the display.)
The muting circuit is activated to cut noise between
stations.
In this mode, FM broadcasts are received in
monaural, regardless of whether they are broad-
cast in monaural or stereo.
Set to the mono mode if there is much noise in the
stereo mute mode (with “AUTO” displayed) or if
the signals are weak.
This button will not function when receiving MW and LW
broadcasts.
RECEIVER DISPLAY
oo 6 © 609
MONO:
The reception
These indicate
the band being
received.
This lights when signals
are received from the re-
mote contro! unit.
EMORY button is pressed during presetting.
This lights when the sta-
tion is tuned in Foor
©6866 @€@e@ee6@ ©8026 6
frequency,
function, time, and timer set-
tings are displayed here.
BAND (FM/MW/LW) selector button
The band switches between FM and MW, LW each time this button
is pressed.
AUTO TUNING UP and DOWN buttons
These are used to tune in MW, LW and FM stations, and for
corrections when setting the time and timer.
SDB (Super Dynamic Bass) button
Press this button for more powerful bass sound.
Press again to turn the SDB function off.
FUNCTION selectors
Use these to select the program source.
TIME SET button
This is used when setting the timer and the current time, and when
checking the timer settings, etc.
CLEAR button
in. rosa! F : :
N
f
M
This
is
used
to
change
the
current
time
and
the
timer
settings.
epee buttons for FM/AM presetting, time set- TIMER button
’
This
is
used
to
set
the
timer.
Timer START MODE button
Use this button to select the function when setting the timer.
Timer STANDBY button
Press this button so that the timer will operate at the set times.
DISPLAY TIME/FUNCTION button
Press this button to switch the display between the function and the
time.
BASS control
Use this to adjust the bass.
TREBLE control
Use this to adjust the treble.
BALANCE control
Use this to adjust the balance between the volume of the left and
right channels. The volume is the same for the left and right
channels when the control is at the center.
ON: Lights when the timer on time is set.
OFF: Lights when the timer off time is set.
This indicates the preset
number.
02.50 =F3
This flashes for about 10 seconds when the lie) - STEREO AUTO MONO
hd : é ; a
This lights to in-
dicate that the
timer is set.
ON TIMER 7
OFF SLEEP
This | This fights when the sleep timeris set. | when the sleep timer is set.
NOTE:
@ The timer standby mark *
not set.
@ ” will not light if the current time is
These indicate the FM reception mode.
STEREO: Lights when receiving stereo broadcasts.
AUTO: Lights when the auto mode is set with the FM mode
button.
Lights when the monaural mode is set with the FM mode
button.
MONO: