DeWalt DCD470 - Page 35

33
ENGLISH
Charge
DeWALT
battery packs only with designated
DeWALT
chargers. Charging battery packs other
than the designated
DeWALT
batteries with a
DeWALT
charger may make them burst or lead to
other dangeroussituations.
Do not incinerate the batterypack.
USE (without transport cap). Example: Wh rating
indicates 108 Wh (1 battery with 108 Wh).
TRANSPORT (with built-in transport cap). Example:
Wh rating indicates 3 x 36 Wh (3batteries of 36 Wh).
Battery Type
The DCD470 operates on a 54 volt batterypack.
These battery packs may be used: DCB546 and DCB547.
Refer to Technical Data for moreinformation.
Package Contents
The package contains:
1 Drill
1 Side handle
1 Chuck key
1 Chuck key holder
1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)
2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)
3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are not included
with Nmodels.
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual beforeuse.
Wear earprotection.
Wear eyeprotection.
Visible radiation. Do not stare intolight.
Date Code Position (Fig. A)
The date code
14
, which also includes the year of manufacture,
is printed into thehousing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Battery
2
Battery release button
3
Main handle
4
Top handle
5
Side handle
6
Speed selector knob
7
Trigger switch
8
Worklight
9
Forward/reverse button
10
13 mm keyed chuck
11
Chuck key
12
E-Clutch® indicator
13
DeWALT
Tool Tag
mounting holes
Intended Use
The DCD470 right angle drill is designed for professional drilling
at various work sites (i.e., construction sites)
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
These heavy-duty right angle drills are professional powertools.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Torque

WARNING: This is a high-torque drill. To reduce the risk
of serious personal injury, ALWAYS hold tool firmly with
both hands in the proper position for operation asshown.
Torque is the twisting action the drill produces in regards to
the rotating bit. As the drill bit meets resistance in the material
being drilled, the motor responds by adjusting the output
torque to meet the requirement up to the maximum capacity of
the motor and gearsystem.
Bracing the Tool (Fig. C, H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold or brace the tool securely in anticipation of
a suddenreaction.

WARNING: To reduce the risk of serious personal injury,
NEVER brace the tool against the batterypack.
With hands in the proper hand position (also refer to Fig. H),
brace the tool as shown in FigureC.
The bit rotates clockwise when the tool is in the forward
position and counterclockwise when the tool is in the reverse
position. Using proper hand position, brace the side handle
5
or tool body against a stud for better support (Fig.C).
Clutch
The DCD470 is equipped with a mechanical slip clutch. The
clutch is active when the low speed (1) is selected. When the
bit or cutter bites into the workpiece, the clutch will slip and a