DeWalt DCN693 - Page 11

9
ENGLISH
1. Using the key
11
provided, loosen the two screws
27
on either side of the unit. Refer
toFigureO.
2. Remove the return system
28
from the unit. Refer to FigureP.
Fig. O
11
27
Fig. P
28 36
3. Slide the spring rail clip
29
off of the spring rail
30
. Refer to FigureR.
4. Twist and remove the spring bumper
31
and remove the washer
32
and return spring
33
.
Refer to FigureR.
5. Mount the new return spring and washer on to the spring rail
30
. While compressing the
spring with the washer near the opposite end of the rail, twist on the new spring bumper
until it is past the groove
34
for the spring railclip.
6. Mount the new spring rail clip securely and position the bumper against theclip.
7. Repeat steps 3–6 for the secondspring.
NOTE: Check the return of the profile by sliding the profile
35
up the spring rail and letting it
go. It should return due to the force from thesprings.
8. Slide the return system
28
back into the unit. It is important to try the alignment of the
profile and the flywheel before screwing the return system back on to the unit. This can be
done by connecting a battery and pushing then releasing the nose of the unit against a
bench or hard surface. This will start the motorspinning.
Fig. Q
29
30
31
Fig. R
29
31
32
34
35
33
NOTE: When the profile and the flywheel are correctly aligned, you will hear the motor coast
back down from full speed. If the profile and the flywheel are not correctly aligned, the motor
it may not start up, may slow down much faster than normal along with a loud grinding
noise from the unit. If this happens remove and reseat the returnsystem.
9. Once the return system is correctly seated, open the provided sachet of Loctite®* and apply
a small amount on the thread of the two screws
27
and remount the two screws using the
key and tightensecurely.

WARNING: Always test the unit by firing short nails in to soft wood, to ensure that the tool
is working properly. If tool does not operate properly, contact a recognized
DeWALT
service
centerimmediately.

WARNING: Loctite® sachet contents may irritate eyes, skin, and respiratory syetem.
Use entire contents on opening. Do not breath fumes. Do not get in eyes or on skin or
clothing. Use only in a well ventilated area. Keep out of reach of children. FIRST AID
TREATMENT:Contains polyglycol dimethacrylate, polyglycol oleate, propylene glycol,
titanium dioxide, and cumene hydroperoxide. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomitting. If breathed in move person to fresh air. If in
eyes, rinse with water for 15 minutes. Obtain medical attention. If on skin, rinse well with
water. If on clothes, removeclothes.
*Loctite® is a registered trademark of HenkelCorp.
Fig. S
Fig. T
27
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty
service in case there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,
your registration of ownership will serve as your proof ofpurchase.
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer SafetyAct.
Register online at www.
DeWALT
.com/register.
Three Year Limited Warranty
DeWALT
will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.
DeWALT
.com or call 1–800–4-
DeWALT
(1–800–433–9258). This warranty does not apply
to accessories or damage caused where repairs have been made or attempted by others. THIS
LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so these
limitations may not apply to you. This warranty gives you specific legal rights and you may have
other rights which vary in certain states orprovinces.
In addition to the warranty,
DeWALT
tools are covered byour:
1 YEAR FREE SERVICE
DeWALT
will maintain the tool and replace worn parts caused by normal use for free any time
during the first year after purchase. Nailer wear items such as return springs, driver blades, and
bumpers are not covered.
2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120, DCB127, DCB201, DCB203, DCB203BT,
DCB207, DCB361
3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS
DCB200, DCB204, DCB204BT, DCB205, DCB205BT, DCB206,
DCB606, DCB609
NOTE: Battery warranty voided if the battery pack is tampered with in any way.
DeWALT
is not
responsible for any injury caused by tampering and may prosecute warranty fraud to the fullest
extent permitted bylaw.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your
DeWALT
Power Tool, Laser, or
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for
a full refund – no questionsasked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,
call 1–800–4-
DeWALT
(1–800–433–9258) for a freereplacement.