DeWalt DCS777 - Page 40

38
ENGLISH
For example, the Transport Wh rating
Example of Use and Transport Label Marking
might indicate 3x36 Wh, meaning 3
batteries of 36 Wh each. The Use Wh
rating might indicate 108Wh
(1battery implied).
Storage Recommendations
1. The best storage place is one that is cool and dry away from direct
sunlight and excess heat or cold. For optimum battery performance and
life, store battery packs at room temperature when not inuse.
2. For long storage, it is recommended to store a fully charged battery
pack in a cool, dry place out of the charger for optimalresults.
NOTE: Battery packs should not be stored completely depleted of charge.
The battery pack will need to be recharged beforeuse.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the charger
and the battery pack may show the following pictographs:
Read instruction manual beforeuse.
See Technical Data for chargingtime.
Do not probe with conductiveobjects.
Do not charge damaged batterypacks.
Do not expose to water.
Have defective cords replacedimmediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indooruse.
Discard the battery pack with due care for theenvironment.
Charge
DeWALT
battery packs only with designated
DeWALT
chargers. Charging battery packs other than the designated
DeWALT
batteries with a
DeWALT
charger may make them burst
or lead to other dangeroussituations.
Do not incinerate the batterypack.
USE (without transport cap). Example: Wh rating indicates 108
Wh (1 battery with 108 Wh).
TRANSPORT (with built-in transport cap). Example: Wh rating
indicates 3 x 36 Wh (3batteries of 36 Wh).
Battery Type
The DCS777 operates on a 54 volt batterypack.
These battery packs may be used: DCB546, DCB547, DCB548. Refer to
Technical Data for moreinformation.
Package Contents
The packagecontains:
1 Partly assembled machine
2 Hex keys (4mm and 6mm)
1 216mm TCT saw blade
1 Material clamp
2 Battery packs (T2 model)
1 Charger (T2 model)
2 Base extention handles and installation hardware
1 Instruction manual
• Check for damage to the tool, parts or accessories which may have
occurred duringtransport.
• Take the time to thoroughly read and understand this manual prior
tooperation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual beforeuse.
Wear earprotection.
Wear eyeprotection.
Keep hands away fromblade.
Keep hands 100 mm from either side of sawblade.
Do not stare directly into the lightsource.
Carryingpoint.
Date Code Position (Fig.B)
The Date Code
32
, which also includes the year of manufacture, is printed
into thehousing.
2019 XX XX
Year of Manufacture
Description (Fig.A–D)

WARNING: Never modify the power tool or any part of it. Damage or
personal injury couldresult.
1
On/off switch
2
Guard lock up release lever
3
Fixed upper guard
4
Outer flange
5
Blade bolt
6
Lower blade guard
7
Saw blade
8
Sliding fence lock knob
9
Fixed table
10
Kerf plate
11
Mitre arm
12
Mitre latch
13
Rotating table/mitre arm
14
Mitre scale
15
Sliding fence
16
Material clamp
17
Rail lock knob
18
Bevel clamp handle
19
Bevel scale
20
Bench mounting holes
21
Lock down pin
22
Rails
23
Saw head
24
Hex wrenches (Fig. D)
25
Battery pack
26
Battery pack release button
27
Fuel gauge button
28
Lock off switch
29
Bevel override button
30
Dust extraction port
31
Base extention handles
32
Date code
Intended Use
Your
DeWALT
cordless compact mitre saw has been designed for
professional cutting wood, wood products and plastics. When using the
appropriate saw blades, sawing aluminum is also possible. It performs the