DeWalt DE7260 - Markings on Tool; Package Contents; Description (Fig. A)

8
ENGLISH
• This product was designed to be used as astand for
mitre saws. The stand will support up to 136 kg. Any misuse
or abuse can result in product damage or personal injury.
• Do not stand on the work table. It is unsafe to climb, sit
or stand on the stand. Do not use the support extensions as
aladder or scaffolding.
• Properly secure the mitre saw to the stand before
operation. Follow the mounting instructions carefully. Fasten
the tool to the saw mounting rails securely as instructed.
• Place the stand on aflat and level surface to prevent
rocking or tipping.
• Take care during the raising and lowering of the product
to reduce the hazard of pinching hands and fingers.
• Check the legs and other supports to see that they are
properly locked in place before operation.
• Do not modify or use the stand for any operation for
which it is not intended.
• If protection or adjustment device or weld is damaged,
no longer use this rolling mitre saw stand.
Package Contents
The package contains:
2 Mounting rails
1 Foot
2 Wheels
1 Leg extension
1 Hex wrench
1 Vertical lock knobs
1 Horizontal lock knobs
1 Handle
1 Work support extension arm
1 Work support
1 Stop plate
1 Activating lever
Hardware bag 1:
2 Axles
2 Bushings
4 Washers
2 Nuts
Hardware bag 2:
4 M8 × 16 mm button head screws
4 Curved washers
1 M6 × 10 mm button head screw
1 M6 lock washer
1 M8 × 21 mm button head screw with thread locking patch
1 M8 lock washer
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Batteries
Chargers/Charge Times (Minutes)
DE7260
DC
Weight
Read instruction manual before use.
Batteries
Chargers/Charge Times (Minutes)
DE7260
DC
Weight
Do not cut packaging contents.
Batteries
Chargers/Charge Times (Minutes)
DE7260
DC
Weight
Pinch and Impact Hazard.
Date Code Position (Fig. B)
The date code
33
which also includes the year of manufacture,
is printed into the housing.
Example:
2017 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1
Mounting rails
2
Foot
3
Wheels
4
Leg extension
5
Hex wrench
6
Vertical lock knobs
7
Horizontal lock knobs
8
Handle
9
Work support extension
arm
10
Work support
11
Stop plate
12
Activating lever
13
Axles
14
Bushings
15
Washers
16
Nuts
17
M8 × 16 mm button head
screws
18
Curved washers
19
M6 × 10 mm button head
screw
20
M6 lock washer
21
M8 ×21 mm button head
screw with thread locking
patch
22
M8 lock washer
Intended Use
This rolling mitre saw stand is designed for use with DeWALT
mitre saws. If you have any problem with alignment or
mounting, consult an authorised DeWALT repair agent.
DO NOT use under wet conditions or in the presence of
flammable liquids or gases.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use this
tool.
DO NOT transport persons or other loads with the ROLLING
MITRE SAW STAND.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or