DeWalt DW03050 - Measuring an Angle

14
ENGLISH
- Press to select .
- Press to display the Measurement Type Menu
(Figure E 3).
- Press the arrow buttons to select .
- Press .
6. Point the laser at the lowest point of the wall or object
whose height you need to measure (Figure T 2).
7. Press to take the measurement.
8. Point the laser at other points on the wall or object (Figure T 3).
9. When ready, press to take the measurement.
10. On the bottom line of the screen, view the height of the wall
or object (Figure T 4).
Positioning Studs
When you are framing a wall, use the Stakeout feature to easily
mark the position of each stud (Figure U).
1. Point the tool's laser (Figure A 1) toward a wall or object, and
not toward anyone's eyes.
2. Press (Figure A 3) to turn the tool on and display the
red laser dot.
3. Make sure the tool position setting (Figure C 4) is set to to
measure from the back of the tool.
4. Select as the measurement type.
- Press to display the Main Menu (Figure E 2).
- Press to select .
- Press to display the Measurement Type Menu
(Figure E 3).
- Press the arrow buttons to select .
- Press .
5. Determine the distance between each stud, for example, 12".
6. Press and until the top number on the screen is set to
the distance from the right edge of one stud to the left edge
of the next (e.g., 12") (Figure U 1).
7. Line up the back of the tool with the right edge of the last
stud that is nailed in (Figure U 2).
8. Press to start measuring the distance as you slowly
move the tool to the right.
9. Continue moving the tool to the right until the bottom
number on the screen is 0.00 in (Figure U 3).
10. Press to stop measuring.
11. Using a pencil, mark the location where the left edge of the
stud should be nailed into the wall frame.
12. Nail the left edge of the stud at the marked location.
13. For each remaining stud in the wall frame, repeat steps 7-12
(Figure U 4).
Measuring an Angle
If you need to determine the angle at which something is
positioned, use the tool to measure that angle (Figure W).
1. Point the tool's laser (Figure A 1) toward a wall or object, and
not toward anyone's eyes.
2. Press (Figure A 3 to turn the tool on and display the
red laser dot.
3. Make sure the tool position setting (Figure C 4) is correct for
taking the measurement.
4. Select as the measurement type.
- Press to display the Main Menu (Figure E 2).
- Press to select .
- Press to display the Measurement Type Menu
(Figure E 3).
- Press the arrow buttons to select .
- Press .
5. Position the tool at the angle to be measured (Figure W 1).
6. Press to take the measurement.
7. View the angle measurement on the screen (Figure W 2).
Using the Tool as a Level
1. Point the tool's laser (Figure A 1) toward a wall or object, and
not toward anyone's eyes.
2. Press (Figure A 3) to turn the tool on and display the
red laser dot.
3. Select as the measurement type.
- Press to display the Main Menu (Figure E 2).
- Press to select .
- Press to display the Measurement Type Menu
(Figure E 3).
- Press the arrow buttons to select .
- Press .
4. Place the tool in the vertical or horizontal position on the
surface that you want to check is level (Figure V 1).
5. On the tool's screen, view the position of the white bubble
on the vial (Figure V 2).
Using the Tool With
You can use the tool's Bluetooth® capability to pair it with the
DEWALT® Tool Connect™ application on your cell phone or
tablet, and then mark up room photos with the measurements
you have taken.
1. From either or download the DEWALT® Tool
Connect™ application to your cell phone or tablet.
2. Using the DEWALT® Tool Connect™ application, capture
the room or space for which you want to record the
measurements, by taking room photos.
3. On the DW03050 or DW03101 keypad, press to turn
on the tool.
4. If appears on the screen (Figure C 2), turn on the
Bluetooth® connection.
- On the keypad, press to display the main menu.
- Select .
- Press ∑ Press to turn on the Bluetooth® connection.
5. Use the DEWALT® Tool Connect™ application to pair your
cell phone or tablet to the DW03050 or DW03101, and then
mark up photos with the measurements you have taken.
THE Bluetooth® WORD MARK AND LOGOS ARE REGISTERED
TRADEMARKS OWNED BY BLUETOOTH SIG, INC. AND ANY USE
OF SUCH MARKS BY DEWALT IS UNDER LICENSE. APPLE AND THE