DeWalt DW080LGS - Advanced Operation and Connectivity; Setting the Amount of Slope; Arrow Buttons Functionality; Connection Buttons and Bluetooth

ENGLISH
13
Setting the Amount of Slope
1. Turn on Slope Mode.
2. Select the desired axis.
3. Use the Arrow buttons (Fig.
B
,
6
and
7
) to tilt the laser
rotor head up and down.
Arrow Buttons (Fig.
A
,
R
)
The arrow buttons (Figure
A
6
and
7
) are used for different
functions depending on the operating mode of the laser unit.
• In Self-Leveling Horizontal Mode, the arrow buttons
rotate the direction of the laser beam clockwise or counter-
clockwise during rotation, or adjust the position of the laser
beam clockwise or counter-clockwise during Scan Mode.
• In Self-Leveling Vertical Mode, the arrow buttons rotate
the direction of the laser beam clockwise or counter-
clockwise during rotation, or adjust the position of the laser
beam clockwise or counter-clockwise during Scan Mode.
• In Slope Mode, the arrow buttons are used to tilt the
laser head.
Connection Buttons
The connection buttons (Figure
A
10
and
13
) provide
different ways to wirelessly connect to the laser.
• Press the radio waves button
(Figure
A
10
) to
connect your cell phone to the Detector which is connected
to the laser.
• Press the Bluetooth button
(Figure
A
13
) to enable
Bluetooth on the laser. If the laser is within 100 ft (30 m),
you can use the Tool Connect application on your
cell phone to control the laser, instead of using the remote.
Also, if the laser is dropped, disturbed, etc., it will send
messages to the Tool Connect application to inform you.
Using the Tool Connect Application
You can use Bluetooth
®
capability to pair the laser with the
DEWALT
®
Tool Connect application on your cell phone, and then
use your cell phone to control the laser (Figure
N
).
1. From either
or , download the
DEWALT
®
Tool Connect application to your cell phone.
2. On the laser keypad, press
to turn the laser on.
3. On the laser keypad, press to turn on Bluetooth
®. (
If
Bluetooth does not turn on, replace the coin cell battery (3V
CR2430) on the bottom of the laser.)
4. Using the DEWALT
®
Tool Connect application, select the
product type (Rotary Laser) and pair your cell phone to the
DW080LRS/DW080LGS.
When the laser is on, the DEWALT
®
Tool Connect application will
display information about the laser:
• A laser safety icon to let you know the laser is on.
• The laser's current settings for RPM, Slope, etc.
• If the current settings are one of the "favorite settings" you
have saved for the laser, it will display the name of that
setting (e.g., Main St - Site 1).
• If the Tracking feature is on, the application will know
where the laser is and will let you know if the laser has
been taken and is now out-of-range.
THE BLUETOOTH® WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED
BY BLUETOOTH SIG, INC. AND ANY USE OF SUCH MARKS BY STANLEY TOOLS IS UNDER
LICENSE. APPLE AND THE APPLE LOGO ARE TRADEMARKS OF APPLE INC., REGISTERED
IN THE U.S. AND OTHER COUNTRIES. APP STORE IS A SERVICE MARK OF APPLE INC.,
REGISTERED IN THE U.S. AND OTHER COUNTRIES. GOOGLE PLAY AND THE GOOGLE PLAY
LOGO ARE TRADEMARKS OF GOOGLE INC.
Turning the Laser On (Fig.
E
,
B
)
1. Insert the fully charged 20V battery pack as shown in
Figure
E
.-
2. Gently press the power button
to power ON the laser.
- The power LED indicator light (Figure
A
9
) will
illuminate.
- Self-leveling mode is activated automatically and the
laser unit will self-level. Once the laser unit is level, the
beam will rotate clockwise once at 600 RPM.
- After 10 sec., Hi Mode (Anti- Drift) is activated
automatically and the Hi LED (Figure
A
8
) will
illuminate.
3. Press the speed/rotation button (Figure
A
3
) to adjust the
rotation speed. The direction can be changed using buttons
6
and
7
.
4. Press the Scan button (Figure
A
4
) to set the laser to
scan in 0°, 15°, 45°, or 90° degree mode.
If you turn ON Slope Mode, the Slope LED (Figure
A
12
)
will light. If using X-axis leveling, the X-axis LED (Figure
A
24
) will light, or if using Y-axis leveling, the Y-axis LED (Figure
A
25
) will light instead.
Calibrating the Laser (Fig. O, P)
Field calibration checks should be done frequently. This section
provides instructions for performing simple field calibration
checks of your
DeWALT
Rotary Laser. Field calibration checks
do not calibrate the laser. That is, these checks do not correct
errors in the leveling or plumbing capability of the laser. Instead,
the checks indicate whether or not the laser is providing a
correct level and plumb line. These checks cannot take the
place of professional calibration performed by a
DeWALT
service center.