DeWalt DW974 - Battery Packs; Charging Procedure

Battery Packs
Your tool uses a 12.0 Volt or a 14.4 Volt DEWALT battery pack. When
ordering replacement battery packs, be sure to include catalog
number and voltage: (12.0 Volt-DW9071) (14.4 Volt-DW9091 or
DW9092). XR PACK™ Extended Run-Time battery packs deliver
25% more run-time than standard battery packs. NOTE: Your tool will
accept either standard or Extended Run Time battery packs.
However, be sure to select proper voltage.
3
English
• CHARGING
• CHARGED
• DELAY
D
W
9
1
1
5
D
A
N
G
E
R
:
W
A
R
N
IN
G
:
15 M
INUTE CHARGER
FLASHING
ON
FAST FLASH•DEFECTIVE PACK
ON
9
.0
v
E
X
T
E
N
D
E
D
R
U
N
T
I
M
E
1
2
.0
v
E
X
T
E
N
D
E
D
R
U
N
T
I
M
E
DW9115
D
A
N
G
E
R
:
W
A
R
N
IN
G
:
R
R
R
R
DW9115
15 MINUTE
CHARGER
DW9104,
DW9106 1 HOUR
CHARGERS
•
C
H
A
R
G
I
N
G
•
C
H
A
R
G
E
D
•
D
E
L
A
Y
1
5
M
I
N
U
T
E
C
H
A
R
G
E
R
F
L
A
S
H
I
N
G
O
N
F
A
S
T
F
L
A
S
H
•
D
E
F
E
C
T
I
V
E
P
A
C
K
O
N
D
W
9
1
1
5
DANGER:
WARNING:
R
FIG. 1
DW9107
1 HOUR CHARGER
Chargers DW9104, DW9106, DW9107,
DW9115
Your battery can be charged in the DW9104, DW9106, DW9107(1
Hour Chargers),or the DW9115 (15 Minute Charger) Be sure to read
all safety instructions before using your charger.
Charging Procedure
These chargers require no adjustment and are designed to be as
easy as possible to operate. Simply place your battery pack into the
receptacle of a plugged in charger (FIG.1) and it will automatically
charge the pack.
DW9104/DW9106/DW9107 (1 HOUR CHARGERS)
1. Plug the charger into an appropriate AC power outlet.
2. Insert the battery pack into the charger, as shown in FIG.1,
making sure the pack is fully seated in the charger. The red
(charging) light will blink continuously indicating that the charging
process has started.
3. The battery pack will be fully charged in about 1 hour. The
completion of charge will be indicated by the red light remaining
ON continuously. The pack is fully charged and may be used at
this time or left in the charger.
DW9115 (15 MINUTE CHARGER)
1. Plug the charger into an appropriate AC power outlet. The charger
will beep twice, the red light will blink and go off.
2. Insert the battery pack into the charger, as shown in FIG. 1,
making sure the pack is fully seated in the charger. The red light
will blink and the charger will beep once indicating the charging
process has started.
3. The battery pack will be fully charged in less than 15 minutes
under most conditions. This will be indicated by the red light
remaining ON and 3 beeps. The pack is fully charged and may
be used at this time or left in the charger.
385360/DW974 etc 5/2/02 11:25 AM Page 3