To Next PageTo Next Page
Need help?Do you have a question about the DeWalt DW997 and is the answer not in the manual?
Keep work area clean, well lit, and free from flammable materials. Keep bystanders away.
Do not abuse cords, use specified chargers, and use battery tools only with designated packs.
Stay alert, dress properly, avoid accidental starting, use safety equipment.
Secure workpiece, use correct tool, do not force tool, disconnect power before adjustments.
Hold tool by insulated surfaces when operating near hidden wiring to avoid shock.
Wear appropriate hearing protection due to potential noise exposure during tool use.
Store tools on their side on a stable surface to prevent tripping hazards.
Be aware of chemical hazards in dust from construction activities; use ventilation and PPE.
Do not incinerate damaged packs. Handle leaks with soap/water/acid. Dispose of responsibly.
Avoid carrying spare battery packs with metal objects to prevent short circuits and burns.
Use only DEWALT chargers for DEWALT battery packs for safety and performance.
Do not store or use battery packs in locations exceeding 105°F (40.5°C).
Never attempt to open or tamper with a battery pack; return damaged packs for recycling.
Information on the Rechargeable Battery Recycling Corporation (RBRC) seal and recycling.
Charge only DEWALT Ni-Cd batteries; other types may burst and cause injury.
Keep charger cavities free of conductive foreign materials to prevent short circuits.
Avoid touching charging terminals with conductive objects due to high voltage.
Do not expose the charger to liquids; this can result in electric shock.
Pull by the plug, not the cord, when disconnecting the charger. Protect the cord.
Use extension cords cautiously, ensuring proper wire size and avoiding damage.
Ensure charger ventilation slots are clear; avoid placing on soft surfaces or near heat.
Do not operate a damaged charger; have it replaced or serviced immediately.
Unplug charger before cleaning. Removing battery pack does not reduce shock risk.
Never connect two chargers together. This is hazardous.
Use chargers only with the power sources specified on the nameplate.
Tune-Up mode balances battery cells for peak capacity; takes up to 8 hours.
Insert battery, press Tune-up button (if available) to start cell equalization.
Plug in charger, insert battery pack, red light indicates charging; full charge in about 1 hour.
Charger may suspend operation if power source is out of limits, indicated by flashing red light.
Charger delays charging if battery is hot; red light flashes long, then short.
Insert battery; charger beeps and red light blinks. Full charge in under 15 mins.
15 min charger detects weak packs with rapid beeps; charges to highest possible capacity.
Charger enters equalize/maintenance mode after full charge; battery stays fresh.
Charge between 65-75°F. Avoid charging below 40°F or above 105°F.
Fast red light flashing indicates a problem; re-insert pack or try a different pack.
Align notch, slide pack firmly into handle until it locks. Press release buttons to remove.
Squeeze trigger to turn on/off. Trigger depth controls speed. Tool has a brake.
Button determines rotation direction and locks tool. Center position locks tool.
Adjusts clutch torque for driving fasteners or selects hammer mechanism for drilling.
Shift lever selects low speed/high torque or high speed/low torque settings.
Grasp chuck halves, rotate to open/close for accessory insertion/removal.
Grasp sleeve, rotate to open/close chuck for accessory insertion/removal.
Loosen screw by striking hex key in chuck with mallet. Unthread chuck by hand.
Use sharp bits, secure workpiece, apply steady pressure, and control twisting action.
Use twist drills, spade bits, or auger bits. Clear chips to prevent overheating.
Use cutting lubricant for most metals. Drill dry for cast iron and brass.
Use carbide tipped bits at high speeds. Apply even force to avoid cracking.
Rotate collar to hammer symbol. Use light force to avoid overheating and stalling.
Select speed/torque range, insert fastener accessory, set torque collar via practice runs.
Blow dust from vents weekly with dry air. Clean exterior plastic with damp cloth.
Recommended accessories are available at extra cost. Contact DEWALT for assistance.
Repairs, maintenance, and adjustments must be done by certified service centers using identical parts.
One-year warranty against defects in materials/workmanship. Excludes accessories and unauthorized repairs.
Return the complete unit within 30 days for a full refund if not completely satisfied.
Call for free replacement of illegible or missing warning labels.
General
