DeWalt XR DCF887 User Manual

ENGLISH
3
English (original instructions)
BRUSHLESS CORDLESS COMPACT IMPACT DRIVER
DCF887
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCF887
Voltage V
DC
18
Type 1/10/20
Battery type Li-Ion
Power output W 400
No load speed rpm
Mode 1 0–1000
Mode 2 0–2800
Mode 3 0–3250
Impact rate ipm 0–3800
Max torque Nm 205
Tool holder mm 6.35
Weight (without battery pack) kg 0.9
Noise values and vibration values (triax vector sum) according to EN62841-2-2:
L
PA
(emission sound pressure level)
dB(A) 96
L
WA
(sound power level)
dB(A) 107
K (uncertainty for the given sound level)
dB(A) 3
Vibration emission value a
h
= m/s
2
22.0
Uncertainty K = m/s
2
2.1
The vibration and/or noise emission level given in this
information sheet has been measured in accordance with
a standardised test given in EN62841 and may be used to
compare one tool with another. It may be used for a preliminary
assessment ofexposure.

WARNING: The declared vibration and/or noise emission
level represents impact tightening of fasteners of the
maximum capapcity of the tool. However if the tool is
used for different applications, with different accessories
or poorly maintained, the vibration and/or noise emission
may differ. This may significantly increase the exposure
level over the total workingperiod.
An estimation of the level of exposure to vibration and/
or noise should also take into account the times when the
tool is switched off or when it is running but not actually
doing the job. This may significantly reduce the exposure
level over the total workingperiod.
Identify additional safety measures to protect the
operator from the effects of vibration and/or noise such
as: maintain the tool and the accessories, keep the
hands warm (relevant for vibration), organisation of
workpatterns.
EC-Declaration of Conformity
Machinery Directive
Brushless Cordless Compact Impact Driver
DCF887
DeWALT declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN62841-1:2015, EN62841-2-2:2014.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at
the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf ofDeWALT.
Markus Rompel
Vice President of Engineering, PTE-Europe
DeWALT, Richard-Klinger-Straße 11,
65510, Idstein, Germany
01.08.2019
WARNING: To reduce the risk of injury, read the
instructionmanual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.

DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

DeWalt XR DCF887 Specifications

General

Voltage	18V
Max Torque	205 Nm
Impacts per Minute	0-3800 IPM
Tool Holder	1/4" Hex
Weight	0.94 kg
Power Output	400 W
Length	134 mm
Hand/Arm Vibration - Impact	22 m/s²
Uncertainty K 1 (Vibration)	1.5 m/s²
Sound Pressure	96 dB(A)
Sound Power	107 dB(A)
Uncertainty K 2 (Sound)	3 dB(A)
Battery Type	Li-Ion
No Load Speed	0-3250 rpm