4
ENGLISH
DECLARATION OF CONFORMITY
THE SUPPLY OF MACHINERY SAFETY
REGULATIONS 2008
18V Chainsaw
DCM565
DeWALT declares that these products described under “technical
data” are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I. 2008/1597
(as amended), EN 62841-1:2015+A11:2022, EN62841-4-1:2020.
The Noise Emission in the Environment by Equipment for use
Outdoors Regulations 2001, S.I. 2001/1701 (as amended),
Schedule8.
L
PA
(measured sound pressure level) 89.5 dB(A)
L
WA
(guaranteed sound power) 102.0 dB(A)
These products conform to the following UK Regulations
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (asamended).
EC-Declaration of Conformity
Machinery Directive
o
18V Chainsaw
DCM565
DeWALT declares that these products described under Technical
Data are in compliance with:
2006/42/EC, EN62841-1:2015, EN62841-4-1:2020.
2000/14/EC, Annex V
L
PA
(measured sound pressure level) 89.5 dB(A)
L
WA
(guaranteed sound power) 102.0 dB(A)
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact
DeWALT at
the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of
DeWALT.
Markus Rompel
Vice-President Engineering, PTE-Europe
DeWALT, Richard-Klinger-Straße 11,
65510, Idstein, Germany
25.08.2021
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment ofexposure.
WARNING: The declared vibration and/or noise
emission
level represents the main applications of the tool. However,
if the tool is used for different applications, with different
accessories or is poorly maintained, the vibration and/or
noise emission may differ. This may significantly increase the
exposure level over the total workingperiod.
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the
job. This may significantly reduce the exposure level over the
total workingperiod.
Identify additional safety measures to protect the operator
from the effects of vibration and/or noise such as: maintain
the tool and the accessories, keep the hands warm (relevant
for vibration), organisation of workpatterns.
DCM565
Voltage V
DC
18
Battery type Li‑Ion
Bar Length cm 30
Maximum Chain Speed (no‑load) m/s 7.3
Maximum Cutting Length cm 26
Oil Capacity ml 115
Weight (without battery pack) kg 3.7
Noise values and vibration values (triax vector sum) according to EN62841‑4‑1.
L
PA
(emission sound pressure level) dB(A) 89.5
L
WA
(sound power level) dB(A) 99.0
K (uncertainty for the given sound level) dB(A) 3.0
Vibration emission value a
h
= m/s
2
3.7
Uncertainty K = m/s
2
1.5
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
English (original instructions)
18V CHAINSAW
DCM565
To Next Page
Loading...
Need help?
General
