DeWalt XR DCS356 Manual

11
ENGLISH
These battery packs may be used: DCB181, DCB181, DCB182,
DCB183, DCB184, DCB187, DCB189, DCB203, DCB204,
DCB205,DCBP034,DCBP520, DCB546, DCB547, DCB548,
DCB549 DCB606, DCB609, DCB612. Refer to Technical Data for
moreinformation.
Package Contents
The package contains:
1 Adaptor for all blades
1 31mm x 43mm Fastcut wood blade
1 Sanding-pad
1 31 mm x 43 mm Wood with nails blade
1 Rigid scraper blade**
1 Blade adaptor hex key
1 Dust extraction adaptor**
1 Cutting guide**
1 100mm Semicircle blade**
25 Assorted sandpaper pieces
1 9.5mm x 43mm Wood detail blade**
1 3mm Carbide grout removal blade (100mm half moon)**
1 Cutting guide hex key**
1 Instruction manual
** Accessory included only with NT models and kits containing
battery andcharger.
NOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. Bmodels include Bluetooth® batterypacks.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by
DeWALT is under license. Other trademarks and
trade names are those of their respectiveowners.
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Visible radiation. Do not stare into light.
Date Code Position (Fig. B)
The date code
25
, which also includes the year of manufacture,
is printed into thehousing.
Example:
2022 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Variable speed trigger
2
LED Worklight
3
Accessory clamp lever
4
Lock on/off button
5
Accessory side mount slots
6
Cut guide block
7
Cut guide arm
8
Battery pack
9
Battery release button
10
Speed selector (DCS356)
Intended Use
This oscillating multi-tool is designed for professional detail
sanding, plunge cutting, flush cutting, removal of excess
materials and surface preparationapplications.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
This oscillating multi-tool is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.

WARNING: Use only DeWALT battery packs andchargers.

WARNING: Risk of lacerations or burns. Do not touch
the sharp edges of accessories at any time. Do not
touch workpiece or blade immediately after operating the
tool. They can become very hot. Handle carefully. Always
allow accessories and workpiece to cool beforehandling.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
NOTE: Make sure your battery pack
1
is fullycharged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
1
with the rails inside the tool’s
handle (Fig. B).

DeWalt XR DCS356 Specifications

General

Voltage	18 V
Oscillations Per Minute	0-20, 000 OPM
Tool-Free Accessory Change	Yes
Variable Speed Trigger	Yes
LED Light	Yes
Power Source	Cordless
Oscillating Angle	1.6°
Quick-Change	Yes
Dust Extraction	No
Battery Type	Lithium-Ion