DeWalt XR LI-ION DCL074 - Page 10

8
ENGLISH
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
NOTE: Make sure your battery pack
10
is fullycharged.
To install the battery pack
10
into the area light, open the
battery compartment door
12
, align the battery pack with the
rails inside the battery compartment and slide it in until the
battery pack is firmly seated and latched. Ensure that it does not
disengage, then close thedoor.
1. To remove the battery pack from the area light, press the
battery release button
11
on the battery pack and firmly
pull the battery packout.
Fuel Gauge Battery Packs (Fig. B)
Some
DeWALT
battery packs include a fuel gauge which consists
of three green LED lights that indicate the level of charge
remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-userapplication.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.

WARNING: Use only
DeWALT
battery packs andchargers.
Suspending/Mounting the Area Light
(Fig.C,D)

CAUTION: When the area light hangs by the hang hook or
hang inset, do not shake the light or the object from which it
hangs. Do not hang the area light from any electrical wires
or anything that is not secure. Personal injury or property
damage mayoccur.

CAUTION: Only use the hang hook or hang inset for
hanging the area light. The hang hook and hang inset are
not intended to support additional weight. Do not attach
or hang anything additional to the light or risk of breakage
mayoccur.

CAUTION: Do not use the hang hook to reach with.
Do not use the hang hook or hang inset to support your
weight in anysituation.

CAUTION: Do not stand underneath the area light when
it is mounted overhead. Serious personal injury or damage
to the light may result if the lightfalls.

CAUTION: Do not mount the area light to theceiling.
Your area light has multiple options for suspending ormounting.
Description (Fig. A, C)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Lens
2
Handles
3
DeWALT
Tool Connect™ button
4
Power button
5
Brightness button
6
Date code (Fig. C)
Intended Use
This area light is designed for professional lightingapplications.
Do not use under wet conditions or in the presence of
flammable liquids orgases.
This area light is a professional powertool.
Do not let children come into contact with the tool. Supervision
is required when inexperienced operators use thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Hang Hook (Fig. C)
The hang hook
7
is provided on the bottom of the area light to
allow suspending thelight.
Hang Inset (Fig. D)
A cord may be used to hang the light by looping it through the
hang inset
13
found on the bottom of thelight.
Screw Threads (Fig. D)
Screw threads, 1/4"-20
8
and 5/8"-11
9
, are provided on the
bottom of the area light to allow mounting to atripod.

CAUTION: Use only with
DeWALT
heavy-duty tripod
to ensure stability when mounted. Refer to Optional
Accessories for moreinformation.
1. Place the tripod's mounting screw into the appropriate
screw thread on the base of thelight and screw the tripod
to thelight.
2. Ensure the light is securelyattached.
Carrying the Area Light (Fig. A)
Carry the area light using one or two of the four side handles
2
.
Never use the side handles to attach the light to anything. Refer
to Suspending/Mounting the AreaLight.
Date Code Position (Fig. C)
The date code which also includes the year of manufacture, is
printed into thehousing.
Example:
2020 XX XX
Year of Manufacture