DeWalt XR LI-ION DCM575 - Protecting the Environment

17
ENGLISH

WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to do
this could result in serious personalinjury.
NOTE: The cutters will dull immediately if they touch the
ground or a nail whilecutting.
To get the best possible performance from your chain saw it is
important to keep the teeth of the chain sharp. Follow these
helpful tips for proper saw chain sharpening:
1. For best results use a 4.5mm file and a file holder or filing
guide to sharpen your chain. This will ensure you always get
the correct sharpeningangles.
2. Place the file holder flat on the top plate and depth gauge
of thecutter.
3. Figure R- Keep the correct top plate
21
filing angle line
of 30° on your file guide parallel with your chain (file at 60°
from chain viewed from the side).
4. Sharpen cutters on one side of the chain first. File from the
inside of each cutter to the outside. Then turn your saw
around and repeat the processes (2,3,4) for cutters on the
other side of thechain.
NOTE: Use a flat file to file the tops of the rakers (portion of
chain link in front of the cutter) so they are about 0.635mm
below the tips of the cutters as shown in FigureS.
5. Figure T- Keep all cutter lengthsequal.
6. If damage is present on the chrome surface of the top plates
or side plates, file back until such damage isremoved.

CAUTION: After filing, the cutter will be sharp, use extra
caution during thisprocess.
NOTE: Each time the chain is sharpened, it loses some of the
low kickback qualities and extra caution should be used. It
is recommended that a chain be sharpened no more than
fourtimes.
Accessories

WARNING: The use of accessories not recommended in
this manual may behazardous.
Replacement chain and bar are available from your nearest
DeWALT authorized service center. For use only with low kick
back bar andchain.
Available bars and chains for DCM575:
• Bar: 40cm service part number 90641855
46cm service part number N500117
• Chain: 40cm service part number 90618541
46cm service part number N500152
MAINTENANCE
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.
The charger and battery pack are notserviceable.
Lubrication
Refer to Saw Chain and Guide Bar Oiling (Fig. L)
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
thetool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed ofproperly.