23
繁體中文
DCB118 充電器具有專為冷卻電池組而設計的內部風
扇。在需要冷卻電池組時,風扇會自動開啟。若風扇
運作不正確或通風槽堵塞,切勿操作充電器。請勿讓
異物進入充電器內部。
電子保護系統
XR 鋰離子工具的設計具有電子保護系統,可保護電池
組,避免過載、過熱或深度放電。
如果電子保護系統啟動,本工具會自動關閉。如果出
現此情況,請將鋰離子電池組放進充電器直到電力
全滿。
牆面安裝
這些充電器經過精心設計,可以安裝在牆面上或立在
桌面或工作表面上。若採用牆面安裝,請將充電器安
裝在電源插座連接範圍內的位置,並遠離角落或可能
阻礙空氣流動的障礙。將充電器的背面用作在牆面上
確定安裝螺絲位置的型板。使用長度至少 25.4 mm、
螺頭直徑為 7–9 mm 的牆用螺絲 (另售) 牢固安裝充
電器,旋進木料的最佳深度為螺絲大約有 5.5 mm 長
度露在木料外。將露出的螺絲與充電器背面的槽對
齊,並完全接合到槽中。
充電器清潔指示
警告:觸電危險。在清潔之前,請將充電器的
插頭從 AC 電源插座上拔掉。使用軟布或非金
屬軟刷,去除充電器外部的污垢和油脂。請勿
使用水或任何清潔劑。切勿讓任何液體進入工
具;也不要讓工具的任何部分浸入液體中。
電池組
所有電池組之重要安全指示
購買更換電池組時,務必附上目錄號和電壓資料。
包裝內的電池組並未完全充電。在使用電池組和充電
器之前,請先閱讀以下安全指示,並遵循所列的充電
程序。
請閱讀所有指示
•
不要在易爆環境,如有易燃液體、氣體或粉塵的
環境中進行充電或使用電池。將電池組放進充電
器或拆除電池可能會點燃粉塵或氣體。
•
切勿強行將電池放進充電器。切勿以任何方式改
裝電池組以在不相容的充電器中使用,否則電池
組可能會破裂,導致嚴重人身傷害。
•
只可使用 DeWALT 充電器為電池充電。
•
請勿將水分或其他液體飛濺到電池組或將電池組
浸沒。
•
請勿在溫度可能達到或超過 40˚C (104˚F) 的地方
(例如夏季的室外貨棚或金屬建築物) 儲存或使用
本工具及電池組。
•
即使電池組已嚴重損毀或磨損,請勿焚燒電池
組。 電池組可能會在火中爆炸。焚燒鋰離子電池
組時會產生有毒氣體和物料。
•
如果電池液體接觸到皮膚,請立即以中性肥皂和
清水沖洗接觸範圍。若電池液體進入眼睛,請睜
開眼睛,用清水沖洗 15 分鐘或直到不適感消失為
12
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
止。如果需要接受治療,電池的電解質由液化有
機碳酸鹽和鋰鹽構成。
•
開啟的電池中的物質可能會導致刺激呼吸道。請
轉移至空氣流通處。如果症狀持續,請尋求醫療
協助。
警告:燒傷危險。電池液如遇到火花或火焰可
能會引起燃燒。
警告:不論是因為任何理由,都不要嘗試打開
電池。如果電池組的外殼破裂或損毀,請勿放
進充電器。切勿撞擊、摔落或損毀電池組。切
勿使用受到重擊、墜落或出現其他損壞情況的
電池組或充電器(例如釘子刺穿、以鎚子敲打
或踩踏)。否則可能會引起觸電或觸電致死。
損毀的電池組應該送回維修中心進行回收。
警告:火災危險。切勿在儲存或搬運電池組
時讓金屬物件接觸暴露的電池兩極。例如,不
要將電池組放在帶有鬆動的釘子、螺絲、鑰匙
等的地方 (如圍裙、口袋、工具箱、產品包裝
箱、抽屜等)。
小心:不使用工具時,請將工具放在穩定的表
面上,以免導致絆倒或墜落等危險。一些具有
大型電池組的工具可以直立但可能會輕易被
撞到。
運輸
警告:火災危險。電池運輸途中,若兩級意
外接觸導電材料,可能會引發火災。運輸電池
時,確保電池兩級受到保護,並與可能接觸兩
級並導致短路的材料良好絕緣。
DeWALT 電池符合行業和法律標準 (包括聯合國危險貨
物運輸建議書、國際航空運輸協會 (IATA) 危險物品處
理規則、國際海運危險物品 (IMDG) 處理規則以及國
際公路運送危險物品歐洲協議 (ADR)) 規定的所有適用
運輸規章。鋰離子電池和電池組均已根據《聯合國危
險貨物運輸建議書測試與標準手冊》第 38.3 節的規定
進行測試。
大多數情況下,不會將運輸
DeWALT 電池組分歸為完
全管制的第 9 類危險品。一般只有在運輸中包含額
定能量大於 100 瓦時 (Wh) 的鋰離子電池時,才會將
其分歸為完全管制的第 9 類危險品。所有鋰離子電
池外殼上均標註有瓦時等級。此外,由於規章的複雜
性,
DeWALT 不建議對鋰離子電池組單獨採用空運,不
論其額定能量是多少瓦時,都是如此。若電池組的額
定能量不超過 100 Whr,可以同時空運工具與電池組
(組合套件)。
無論運輸是否納入完全管制範圍內,運輸方均有責
任諮詢瞭解針對包裝、標籤/標記及單據要求的最新
規定。
手冊本節資訊基於良好商譽原則提供,在編製文件時
被視為準確無誤,但不提供任何明示或暗示的保證。
買方負有確保其行為遵守適用法規的責任。
運輸 FLEXVOLT
TM
電池
DeWALT FLEXVOLT
TM
電池有兩種模式:使用與運輸。
使用模式:若 FLEXVOLT
TM
電池單獨使用或在 DeWALT
18/20V 產品中使用時,將作為 18/20V 電池運作。若
4
English
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
powertool.
Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
Electrical Safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed orgrounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electricshock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f) If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk
of electricshock.
English (original instructions)
CORDLESS RECIPROCATING SAW
DCS388
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make
DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCS388
Max/Rating Voltage V
DC
60/54
Battery type Li-Ion
Max. power output W 1550
No load speed min
-1
0–3000
Stroke length mm 28.6
Cutting capacity in wood/metal profiles/
plastic tubes
mm 300/130/160
Weight (without battery pack) kg 3.54
Battery pack DCB606 DCB546
Battery type Li-Ion Li-Ion
Voltage V
DC
20/60 18/54
Capacity Ah 6.0/2.0 6.0/2.0
Weight kg 1.05 1.05
Charger DCB118
Mains voltage V
AC
220-240
Battery type 20/60Li-Ion
Approx. charging time
of battery packs
min 22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah)
45 (3.0 Ah) 60 (4.0 Ah) 75 (5.0 Ah)
60 (6.0 Ah)
Weight kg 0,66
The DCB118 charger accepts 18/20V Li-Ion XR and
XRFLEXVOLT
TM
battery packs (DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185 DCB546 and DCB606).
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
ZV DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
12
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
4
English
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
powertool.
Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
Electrical Safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed orgrounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electricshock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f) If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk
of electricshock.
English (original instructions)
CORDLESS RECIPROCATING SAW
DCS388
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make
DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCS388
Max/Rating Voltage V
DC
60/54
Battery type Li-Ion
Max. power output W 1550
No load speed min
-1
0–3000
Stroke length mm 28.6
Cutting capacity in wood/metal profiles/
plastic tubes
mm 300/130/160
Weight (without battery pack) kg 3.54
Battery pack DCB606 DCB546
Battery type Li-Ion Li-Ion
Voltage V
DC
20/60 18/54
Capacity Ah 6.0/2.0 6.0/2.0
Weight kg 1.05 1.05
Charger DCB118
Mains voltage V
AC
220-240
Battery type 20/60Li-Ion
Approx. charging time
of battery packs
min 22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah)
45 (3.0 Ah) 60 (4.0 Ah) 75 (5.0 Ah)
60 (6.0 Ah)
Weight kg 0,66
The DCB118 charger accepts 18/20V Li-Ion XR and
XRFLEXVOLT
TM
battery packs (DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185 DCB546 and DCB606).
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
ZV DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
12
ENGLISH
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by
DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
4
English
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
powertool.
Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
Electrical Safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed orgrounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electricshock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f) If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk
of electricshock.
English (original instructions)
CORDLESS RECIPROCATING SAW
DCS388
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make
DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCS388
Max/Rating Voltage V
DC
60/54
Battery type Li-Ion
Max. power output W 1550
No load speed min
-1
0–3000
Stroke length mm 28.6
Cutting capacity in wood/metal profiles/
plastic tubes
mm 300/130/160
Weight (without battery pack) kg 3.54
Battery pack DCB606 DCB546
Battery type Li-Ion Li-Ion
Voltage V
DC
20/60 18/54
Capacity Ah 6.0/2.0 6.0/2.0
Weight kg 1.05 1.05
Charger DCB118
Mains voltage V
AC
220-240
Battery type 20/60Li-Ion
Approx. charging time
of battery packs
min 22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah)
45 (3.0 Ah) 60 (4.0 Ah) 75 (5.0 Ah)
60 (6.0 Ah)
Weight kg 0,66
The DCB118 charger accepts 18/20V Li-Ion XR and
XRFLEXVOLT
TM
battery packs (DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185 DCB546 and DCB606).
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
ZV DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.